Bedienungsanleitung Inverto IDLV-5000P (Seite 9 von 16) (Englisch)

509864

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Multicast IP Addr:• Enter the IP address of the multicast stream for the transport stream over IP.

Multicase UDP Port:

• Enter the UDP port number of the TS over IP stream.

Protocol: • select the protocol for multicast: UDP or RTP.

Output Smoothing:• set the quality of TS which comes from the TS/IP input.

Auto:• the bit rate is variable.

Disable:• the unit let the TS pass by.

Fixed Rate:• the bit rate is xed.

TS Bit Rate:• set the bit rate of the TS comes from the TS/IP input. The setting is only valid when the output

smoothing is congured as Fixed Rate.

5.2 OUTPUTS MENU

Under Outputs Menu, you can monitor and congure the parameters of the CI, AV decoder, ASI out, ASI2/SDI

out, Mux (A), BISS, SDI out and TS over IP output (B).

Note:

(A) The Mux menu is showed only if the functional block is enabled. Refer to section ‘Optional Function’.

(B) The Ethernet menu is showed only if the IP streaming in/out board is installed and the TS/IP streaming board

is set to “IP Out”. Refer to section ‘Optional Function’.

5.2.1 BISS Menu

It includes Biss Mode, Biss 1 Setup and Biss E Setup

Biss Mode: Set Biss mode, can select OFF, Biss E or Biss 1

Biss 1 Setup: set Biss 1, password is required

Biss E Setup: set Biss E, ID number and password are required

5.2.2 CI Menu

There are two PCMCIA slots for inserting CAM for de-encrypting program from the input signal.

Before setting CI, ensure the signal from ASI input is locked or the Tuner locks on the correct Transponder (this

depends on in which signal the encrypted program carried). The ‘Tuner Lock’ LED will ‘on’ in green.

There are 3 submenus: ‘CI Source’, ‘Setup’ and ‘CAM name’ which allow you to set or select the parameters of

the CI.

1. CI Source: press the <ENTER> key, then use <UP> or <DOWN > key select Tuner or ASI1 input or ASI2

input or TS/IP input (only when the TS/IP is set “IP In”, refer section 5.2.7 for details) to set the signal source of

descrambling, press <ENTER> key to save or press <EXIT> key to scrap.

2. Setup: under this sub menu, you can see all program names from the source of CI that was set in ‘CI Source’

previously. All free programs are marked with ‘Free’ in the rst row.

To select which program to be de-encrypted, press the <UP> or <DOWN>key to roll up and down the program

names and press <ENTER> key to change the status of the corresponding program (only encrypted program

could be selected). Three different statuses could be set:

Slot 1 (de-encrypted with upper CAM inserted)

Slot 2 (de-encrypted with lower CAM inserted)

Bypass (no de-encryption).

The status will be shown in the rst row on the LCD display. Conrm this setup when leaving this sub menu,

press <ENTER>key to save or press <EXIT>-key to scrap.

The de-encrypted program could be delivered to other functional blocks, like A/V decoder, ASI1, ASI2, SDI, Mux

and TS/IP output (refer to section 5.2.3~5.2.8 for more).

3. CAM name: under this sub menu, you can see the names of CAM modules.

Outputs

Decoder ASI1 ASI2 SDI Ethernet MuxBISS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inverto IDLV-5000P Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info