Bedienungsanleitung Inverto IDLV-5000P (Seite 11 von 16) (Englisch)

509864

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

5.2.4 ASI1

You can congure the settings of ASI1 in this menu.

ASI1 Source: Press the <ENTER> key and use the <UP> or <DOWN> key to roll up or down to select the signal

source of ASI output, there are 5 type of signal source optional:

CI De-encrypted:

1. the de-encrypted transport stream from CI functional block will be delivered to the ASI

output port on the back panel.

TUNER:2. the transport stream from Tuner block will be delivered to the ASI output port on the back panel.

ASI1 Input:3. the transport stream comes from ASI1 input port will be delivered to the ASI1 output port on

the back panel.

ASI2 Input:4. the transport stream comes from ASI2 input port will be delivered to the ASI2 output port on

the back panel.

Mux TS: 5. the transport stream comes from internal Mux functional block will be delivered to the ASI output

port on the back panel.

Note: The Mux TS is valid only when the Mux function block is enabled and turned on. Refer to section ‘Mux’

and section ‘Optional Function’ for how to set the Mux function block.

Press <ENTER> key to save or press <EXIT> key to scrap. A few seconds after the source being selected, the

TS will be delivered to the ASI output port on the back panel.

5.2.5 ASI2

The same conguration method like section of ‘ASI1’

5.2.6 SDI

You can congure the settings of SDI output in this menu.

Audio PID:

• press the <UP> <DOWN> keys to choose the audio PID from 1~4.

Embed Audios:

• there are 4 options: none, one&two, two, and one.

SDI Output Mode:

• congure output mode HD-SDI or SD-SDI

SDI H Offset:

• the range is 0~999

5.2.7 Mux

Note: this Mux menu is showed only when the Mux function block is enabled and turned on. And the Mux is

alternative (refer to section ‘Optional Function’ for how to turn on and set the Mux function block).

Mux Switch: • the internal multiplexer could be switched On/Off. The default value is ‘off’. To activate the

re-Multiplexing function, you should turn on this Mux functional block.

Bit Rate:• should be set to a specied value that doesn’t exceed the Maximum physical limit of the output

medium. For example, to deliver the multiplexed TS to an 8MHz DVB 256QAM modulator, it should not

exceed 55000Kb/s, otherwise overow occurs.

TS ID:• you can congure the TS ID to mark the multiplexed TS. Default value is 1.

Program List:• press the <ENTER> key to enter ‘Mux List’ sub-menu.

It shows all programs detected by IDLV-5000P. The programs could be come from ASI input, Tuner, TS/IP •

input or the internal CI de-encryption block. Use <UP> <DOWN> keys to roll up the program names, and

use <LEFT> <RIGHT> keys to switch among input sources, where a number in front of the program name

indicates the input source: 0-xxxxx displays the program name, which comes from ASI input.

1-xxxxx displays the program name, which comes from TUNER input.

2-xxxxx displays the program name, which comes from TS/IP input

3-xxxxx displays the program name which comes from the CI.

4-xxxxx displays the program name, which comes from ASI2 input.

5-xxxxx displays the program name, which comes from BISS De-encrypted

input.

On ‘Program List’ sub-menu, on the rst row, all encrypted programs are labeled with a ‘$’ sign.

All programs that are being selected to be re-multiplexed are labeled as ‘Pass’, otherwise, the un-selected

programs are labeled as ‘Fobrid’. Use <ENTER> key to selected or un-selected the program being shown.

When leaving the ‘Program List’ sub-menu, a new menu will be shown ‘Conrm changed?’ Press <ENTER> key

to validate all programs just be selected to be multiplexed or to scrap by pressing <EXIT> key.

After a few seconds, the multiplexed TS will be generated and delivered to the specied destination(s).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inverto IDLV-5000P Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info