Bedienungsanleitung Irox HBVR761 UV-X (Seite 3 von 6) (Englisch)

578944

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

86 87

8584

2. GETTING STARTED

2a) BEFORE YOU BEGIN

For best operation,

1. Insert batteries for remote units before doing so for the

 main unit.

2. Position the remote unit and main unit within effective

 transmission range, which, in usual circumstances, is

 20 to 30 meters.

 Note that the effective range is vastly affected by the

 building materials and where the main and remote units

 are positioned.

 Try various set-ups for best result.

 Though the remote units are weather proof, they should

 be placed away from direct sunlight, rain or snow.

 The UV Sensor is to be placed in a location with the

 best possible exposure to the sun.

2b) BATTERY INSTALLATION: REMOTE UNITS

1. Remove the screws on the battery compartment.

2.Select the channel (except UV sensor)

3. Install 2 batteries (UM-3 or “AA” size 1.5V) strictly

 according to the polarities shown.

4. Replace the battery compartment door and secure its screws.

2c) BATTERY INSTALLATION: MAIN UNIT

1. Open the battery compartment door.

2. Install 2 batteries (UM-3 or “AA” size 1.5V) strictly

 according to the polarities shown.

3. Replace the battery compartment door.

2d) LOW BATTERY WARNING

If it's time to replace batteries for the remote sensors or

the unit, the respective low-battery indicator [ ] will

show up on the outdoor temperature display (for the

thermo/hygro sensor), on the UVI display (for the UV

sensor) or on the clock display (for the unit).

2e) HOW TO USE THE TABLE STAND

 OR WALL MOUNTING

The main unit has a removable table stand, which when

connected, can support the unit on a flat surface. Or you can

remove the stand and mount the unit on a wall using the

recessed screw hole.

2f) GETTING STARTED

SETTING UP THE BAROMETER

a. When batteries are installed, the display will shows the

 “hPa” and “mBar”. User should press the [Unit] key to

 the unit of pressure, it will shows “0” and “meter”. User

 can use the [ ] or [ ] (rear panel) keys to change

 to “feet”, or use the [Unit] key to confirm the unit.

b. After user confirmed the unit of height, it will shows

 “10” with “meter” or “32” with “feet”. User can use the

 [ ] or [ ] (rear panel) keys to change to height of

 the place, and use the [Unit] key to confirm the height.

Remark: The default unit of pressure is hPa/mBar, unit of

 height is meter, height is 10 meters. It will use the

 default value if no key is pressure for 60 seconds.

 Thereafter, the setting of the altitude in meters

 can only be done after reinserting the batteries.

SETTING UP THE REMOTE SENSORS

a. Once batteries are in place for the remote unit, they will

 start transmitting temperature and humidity and UV

 readings at around 45 seconds intervals (around 5 min.

 for UV).

 The main unit will also start searching for signals for

 about two minutes once batteries are installed. 10 seconds

 upon successful reception, the outdoors temperatures,

 humidity and UV will be displayed .

b. If no signals are received, blanks “ ” will be displayed.

 Hold [ ] for 2 seconds to enforce another search for

 about 2 minutes. This is useful in synchronizing the

 transmission and reception of the remote and main units.

Repeat this step whenever you find discrepancies between the

reading shown on the main unit and that on the remote unit.

3. WEATHER FORECAST

3a) WEATHER FORECAST

The unit is capable of detecting atmospheric pressure

changes. Based on collected data, it can predict the weather

for the forthcoming 12 to 24 hours.

NOTE:

1.It is not necessary and not possible to adjust the altitude

 of the weather station. After the initial start-up of the

 weather station, a first forecast will be made within the

 first 24 hours of operation.

2. In periods of long stable weather conditions, it becomes

 difficult to make a reliable forecast.

3. The weather forecast is solely calculated on the basis of

 barometric air pressure changes.

4. The probability of a correct weather forecast is

 approximately 70% and is valid for an area of approx.

 20-30 km around the location of the weather station.

5. The forecast “Sunny” means at night “cloudless weather”.

 Fogies not indicated by the weather station as this can

 occur with different weather conditions.

6.If you travel with become impossible due to changes in

 altitude and location. You'll have to wait up to 24 hour so

 that the weather station can calculate a new forecast

 based on the conditions at the new location.

MOUNTING METHOD UV-SENSOR

Mounting on a

flat surface

Mounting to the soil

Mounting to the pole

Place on the stand

Forecast

Symbols

Forecast

Symbols

Sunny Slightly Cloudy Cloudy

SnowyHeavy rainyLittle rainy

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Irox HBVR761 UV-X Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Irox HBVR761 UV-X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info