Bedienungsanleitung Jablocom EyeSee (Seite 14 von 20) (Englisch)

607101

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

- 14 -

7. Advanced

Security detectors

The EyeSee uses advanced technology and 7 types of detectors to recognize movements,

sounds, vibrations, breaking of glass or opening of doors in a protected area.

Detectors’ settings are professionally tuned to provide the best quality of detection while keeping

sufficient resistance against false alarms. The installation wizard configures the detectors according

to your planned use of your camera (indoors/outdoors).

Note: Please note that some of the detectors are designed for indoor use and using them outdoors may cause

unwanted false alarms – i.e. noise detector may be triggered by wind.

Detectors are optimized to protect an area up to 10 x 10 meters.

Infrared motion detector (PIR)

is a very sensitive detector of thermal

activity. It detects the heat of a human

body or the hot engine of a car.

Tilt detector (TILT)

notices even very small change

of camera´s position, e.g. during

unwanted manipulation with the

camera. This is reported as tampering

alarm.

Motion-In-Picture detector (MIP)

constantly analyses the scene and

detects any changes in the picture. You

can mask-out (hide) a part of a picture

where changes will not be detected (e.g.

street traffic, window).

Touch detector (TOUCH)

responds to micro vibrations of

camera body caused e.g. by touching

the camera by hand. Touch detector

should be switched off outdoors. This

is also reported as tampering alarm.

Glass break detector (GBS)

permanently listens to all sounds and

digitally determinates the characteristics

of window breaking. It should be used

for indoor installations only.

Noise detector (NOISE)

uses a microphone to check the

surrounding area for any sound above

the usual level.

Door opening detector (DOOR)

sensitively checks the small pressure changes which are characteristic mark of door or

window opening. It should only be used indoors.

The sensitivity of each detector may be tuned in JabloTool.com (Settings/Advanced/Detectors). You

may even completely disable some detectors if needed.

When any of the detectors is activated while EyeSee is Watching then the camera starts recording

video and reports alarm.

SD card

The EyeSee records video on a SD memory card. It comes with a 2 GB memory card

installed, that allows to store about 3 hours of continuous video record. Thanks to

sophisticated method of recording, when only moving parts of image are saved, the real

recording time is much longer. Usually the camera stores about three days history.

Tips:

• The EyeSee automatically overwrites the oldest records. Your SD card never gets full.

• The size of one frame (single picture in film strip) fluctuates from 40 to 80 kB. Night pictures

are usually twice as large as a day picture.

• If needed, you can further extend recording time by SD card upgrade (up to 32 GB micro SD).

Please see support.jablocom.com /eyesee for detailed instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablocom EyeSee Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablocom EyeSee

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info