Bedienungsanleitung Jablotron CA-1802 - Athos GSM RESET 2 (Seite 3 von 6) (Englisch)

555041

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

GSM car alarm CA-1802 „Athos“ 3/6 MHF57302

Configuration table - be careful to put spaces between words in SMSes (e.g. MASTER RESET EN 2).

SIM entry* SMS instruction Text Description

RESET EN 2

(After which, the

entry is erased

from the SIM)

MASTER RESET EN 2 Mode setting. RESET 2 = alarm is operated by an original remote controller for central locking.

Performing the RESET 2 instruction is indicated by 4 beeps. Consequently, all settings, enrolled

remote controllers and wireless detectors will be erased.

Not applicable MASTER UC uuuu

User code setting – the code allows you to operate the alarm remotely via SMS from unauthorized

phones. uuuu is a new user code, 4 to 8 characters (A–Z & 0–9, case insensitive). Factory default user

code is USER

Not applicable MASTER MC xxxx Master code setting –xxxx is a new master code (A–Z & 0–9, case insensitive). The code allows you

to change the maintenance settings for the car alarm. Factory default master code is MASTER

TEL1 xx...x MASTER TEL1 xx...x

TEL2 xx...x MASTER TEL2 xx...x

TEL3 xx...x MASTER TEL3 xx...x

TEL4 xx...x MASTER TEL4 xx...x

Setting of phone numbers to report alarms to (these phones will also be authorized to control the

alarm via SMS without a user password)

E.g.: MASTER TEL2 +420602123456 will enter the phone number into memory TEL2

MASTER TEL3 0 will erase the memory TEL3.

DIAL1 xx...x

MASTER DIAL1 xx...x

DIAL2 xx...x

MASTER DIAL2 xx...x

DIALA xx...x

MASTER DIALA xx...x

DIALB xx...x

MASTER DIALB xx...x

Setting the phone numbers to dial using Hands free.

E.g.: MASTER DIAL2 +420602123456 will assign the number to the

button of the remote

controller. MASTER DIAL2 0 will erase the number assigned to the

button.

Not applicable MASTER LEARN RC Enrollment of RC-8x controllers - up to 4 controllers can be enrolled, turn the ignition key on before

sending the instruction. To enroll controllers, press and hold buttons

and together for 3

seconds. After you have enrolled all remote controls, turn the ignition key off. By enrolling the first

controller all other controllers previously enrolled will be erased. All the desired controllers should be enrolled in

a single enrollment session.

Not applicable MASTER LEARN INT

(EXT)

JA-8x wireless detector enrollment – see the description in section 5. Up to 8 detectors can be

enrolled. Turn the ignition key on before sending the instruction. To enroll the sensors, insert their

batteries. After you have enrolled all detectors, turn the ignition key off. All desired detectors from a single

group should be enrolled in single enrollment session.

DIP abcdefghij MASTER DIP

abcdefghij

DIP parameter entry – see the DIP table

SET abcdefghij MASTER SET

abcdefghij

SET parameter entry – see the SET table

TELU xx...x MASTER TELU xx...x SIM card validity maintenance call setting (for pre-paid cards) 1x month the xx..x number is called,

call duration 10 s to maintain the validity of SIM cards requiring this.

Not applicable MASTER TXT 01,text

Modifying SMS messages and instructions (see chapter 9.1). The maximum length of a single text

is 30 characters. Information texts (with indices starting at 27) can be modified using the user code

USER (optional). To change instruction texts (indexed by 01 to 26) the MASTER installation code is

always necessary.

*It is not possible to modify access codes or SMS texts to enroll controllers or detectors by storing numbers in the SIM card phone directory

Always use CAPITAL letters when writing into the SIM card!!!

6. DIP parameters

Parameters A to J correspond to DIP switches. Setting is performed by

SMS: MASTER DIP ABCDEFGHIJ

Description

DIP

0 1

A 0 = silent arming/disarming without siren chirps

1 = 10 ms siren chirps when arming/disarming (non backed-up siren)

2, 3, 4 ... 9 = siren chirps when arming/disarming (a siren of another

type) lasting 20, 30, 40, 50, 100, 200, 300 or 500 ms

B Silent alarm

Audible alarm

SMS alarm report only

SMS alarm report and siren sound

phone call

D SMS remote control not

confirmed by SMS reply

SMS remote control instructions

Confirmed by SMS reply

0 = arming control by dialling-in disabled

1 = arming control by dialling from TEL1 enabled

2 = arming control by dialling from TEL1 and TEL2 enabled

3 = arming control by dialling from TEL1, TEL2 and TEL3 enabled

4 = arming control by dialling from all TEL1 to TEL4 enabled

Arming control by dialling

in is not confirmed by

SMS

Arming control by dialling in (see E)

confirmed by SMS to the phone

which called the car alarm

User can not change SMS

Texts

User can change SMS texts by TXT

Sequence

REARM disabled

If the car is not entered within 1

minute after disarming, it will REARM

0 = Immobilization by arming* and by SMS instruction**

1 = Immobilization by arming* and automatically 5 minutes after

ignition is turned off (AUTOIMO) and also by SMS instruction**

2 = Immobilization only by SMS instruction

3 = Immobilization and also by SMS instruction. If disarmed and

ignition is turned off for more than 60 minutes the SMS STATUS is

send as an alert to possible forgotten arming.

Self-location disabled

The car’s location will be sent by

SMS after an IMO instruction has

been performed.

Factory default setting is DIP 1111000000 (bold letters in the text).

By dialling in, you only operate the car alarm, not the central locking.

* When the car is armed, the immobilization circuit is activated. To

activate the circuit after the car has been disarmed, it is necessary to

turn the ignition key on.

** This SMS instruction results in immobilization that can only be

cancelled via an appropriate SMS instruction. Arming or disarming the

car will not mobilize the car in this case.

7. SET parameters

Parameters A to J correspond to SET switches. Setting is performed by

SMS: MASTER SET ABCDEFGHIJ

Description

SET

0 1

A 0 = open door signalling and INP activation while arming are both

disabled

1 = open door signalling and INP activation while arming are

both enabled

2 = INP activation while arming enabled, open door signalling

enabled with a 10 second delay

3 = INP activation while arming enabled, open door signalling

disabled

Voltage detector disabled

Voltage-drop detector enabled

C Not applicable to this mode (a “0” can be entered).

D DOOR input logic:

1 = activated by falling edge (grounding)

2 = activated by rising edge (disconnecting from GND)

E INP1 logic:

1 = activated by falling edge (grounding)

2 = activated by rising edge (disconnecting from GND)

F INP2 logic:

0 = activated by falling edge (grounding), it triggers an alarm also if

disarmed (24 hour reaction)

1 = activated by falling edge (grounding)

2 = activated by rising edge (disconnecting from GND)

G Central locking input logic:

1 = activated by falling edge (grounding)

2 = activated by rising edge (disconnecting from GND)

Jablotron CA-1802 - Athos GSM RESET 2 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron CA-1802 - Athos GSM RESET 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info