Bedienungsanleitung Jablotron CA-1803BT - reset 1 (Seite 2 von 6) (Englisch)

555037

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

GSM car alarm CA-1803BT „Athos 2/6 MHF56603

 via the Internet page www.GSMLink.cz

which is the most

convenient way. To register there you need the registration code

printed on the warranty card and the master code (factory default is

MASTER).

 by sending command SMS messages via a mobile phone, see

table 5.1.

The choice of the correct car alarm mode should be made first. If you

use the car alarm in such a way that it is operated by its own key fobs,

it is necessary to select MODE 1. The settings can be done by storage

in the SIM card (put RESET into the phone directory as a name and

add “1” to the phone number field) or by the SMS command “MASTER

RESET EN 1” which has to be sent to the car alarm’s SIM card

number. Performing a RESET is indicated by 4 beeps. The factory

default is MODE 0 without any function assigned, except that the

immobilization relay switches on after the ignition key has been turned

on. It is possible to put the car alarm to RESET 0 mode also in the

case, that its functionality should be cancelled entirely.

By carrying out a RESET, you delete all the car alarm settings as

well as all the previously enrolled remote controllers and wireless

sensors. See configuration table 5.1 for performing any subsequent

settings.

5. Enrollment of remote controls and detectors

Up to 4 RC-8x remote controllers and up to 8 JA-8x wireless detectors

can be enrolled. The detectors can be enrolled as either internal or

external. When the car alarm is only partially armed, the detectors enrolled

as internal are excluded from the system (see 8.1 for operating the car

alarm). The external detectors perform protection for every type of arming.

Steps to enroll RC-8x controllers:

1. The car alarm should be disarmed, with the ignition on.

2. Send the SMS instruction MASTER LEARN RC

3. The car alarm beeps 3 times and an LED starts to flash.

4. The RC-8x controller is enrolled by pressing buttons

and

simultaneously for approx. 3 sec. A siren chirp confirms the

enrollment. By enrolling the first remote control all other remote controls

previously enrolled will be erased (so enroll all the controllers intended for use,

one by one).

5. Exit enrollment by turning the ignition off. The alarm confirms the enrollment

by sending an SMS message to authorized phones TEL1 to TEL4.

Steps to enroll internal detectors:

1. The car alarm should be disarmed, ignition on.

2. To enroll the internal detectors, send the SMS command MASTER LEARN

INT

3. The car alarm beeps 3 times and an LED starts to flash.

4. The detector is enrolled by inserting a battery. By enrolling the first detector

all detectors enrolled as internal will be erased (so, enroll all the detectors

which will be used as internal ones).

5. Exit enrollment by turning the ignition off. The alarm confirms enrollment by

sending an SMS message to authorized phones TEL1 to TEL4.

Steps to enroll external detectors:

1. The car alarm should be disarmed, ignition on.

2. To enroll the external detectors, send the SMS command MASTER LEARN EXT

3. The car alarm beeps 3 times and an LED starts to flash.

4. The detector is enrolled by inserting a battery. By enrolling the first detector all

detectors enrolled as external will be erased (therefore, enroll all the

detectors which will be used as external ones).

5. Exit enrollment by turning the ignition off. The alarm confirms enrollment by

sending an SMS message to authorized phones TEL1 to TEL4.

If a detector is switched to delay mode, the alarm will provide a 20 second

entrance delay after the detector has been triggered. An exit delay of 20 seconds is

provided to all enrolled detectors after the car alarm has been armed.

If a sensor has been enrolled as an internal one, it can be re-enrolled as an

external one by its enrollment to the desired group.

If a group of detectors should be erased, take the same steps as with

enrollment, except that a “0“ should be added to the instruction (e.g. “LEARN

INT 0“). This starts enrollment and erases previously enrolled detectors. If no

new detectors should be enrolled, only turn the ignition off.

In case of low battery of any enrolled detector the SMS report will be sent to

the first phone number stored in the car alarm’s memory.

Fig. 1: Wiring the alarm in RESET 1 mode. Wiring the alarm this way makes it possible to control the car’s central locking.

max. 4x RC-8x

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron CA-1803BT - reset 1 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron CA-1803BT - reset 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info