GSM car alarm CA-1803BT „Athos“ 4/6 MHF56603
If you want to cha nge only particular DIP or SET param eters, enter x for the
others (i.e.
MASTER SET xx2xxxxxxx will set an extended locking signal for
closing the windows).
* This setting can cause false alarms due to possible inaccuracy in the
determination of GPS coordinates. Such an inaccuracy can appear as
a consequence of an obstructed signal path, low signal level, satellite
interference, etc. It is recommended to use this as only a
complementary function.
8. User instructions
8.1. Remote control arming and disarming
Button
is used to arm and lock the veh icle complete ly. Using the
button the car can be disarmed and un locked. If y ou re-press the
button within 15 second s after arming, part ial arming occurs ( confirmed
acoustically). In t his mode, the int ernal wireless det ectors are not ac tive,
nor is the low voltage sensor. Also n o voltage is supplied for external
sensors. Using the CR-11A module , pressing the buttons
and
together allows y ou to use additional fun ctionality (e.g. sw itching
independent heating).
8.2. SMS control from an authorized phone
Text SMS Description
AM
ARM and lock the car
AM EXT
Partially ARM and lock the car
DM
DISARM and unl ock the car
IMO
STOP (immobilize) the car ( after turnin g ignition key off)
UNIMO
Unblock ( mobilize) th e car
STATUS
Car alarm will re ply w ith status inform ation, e.g. „car
reports: Time: 27.01.04 13:04, Statu s: Armed, Unbl ocked,
Ignition off“.
HELP
The car alarm will reply with a brief list of SMS instructions.
UC xxxx
To change th e user co de. xxxx is the new us er code, 4 to 8
characters (A –Z & 0 – 9). Facto ry default u ser code is
USER
CREDIT
parameter
To obtain the balance of a prepaid S IM card if used . See
13.6-8 for details
AUX
parameter
To operate CR -11A output relays as well as the a ppliances
or circuits th at are co nnected to t hese relay s (see par. 13)
HF abcdef
Hands-free s et adjustm ent:
a – enable ca lls (0= disabled , 1=enabled)
b – auto an swer inc oming ca lls (0= disabled , 1=enable d)
c – microphone sensitiv ity 0 to 9, (5 )
d – speaker v olume 0 to 9, (5)
e - ringing to ne volume 0=m ute to 9= max ., (5)
f – ringing sound 0 to 9, (1)
GPS
Sends inform ation about t he latest dete cted locati on using
GPS coordinat es (Globa l Position S ystem)
SIREN
To activate the siren for 30 seconds
The instruction must contain spaces ( e. g . H F 105551).
If an SMS instru ction is sen t from an unauthorized phone , it is
necessary to put a user code befor e the instruction (default is USER).
Again, a space is nece ssary. An example of arming from an
unauthorized phone: USER AM
SMS instruct ions are no t case-sens itive. Onl y b as i c A SC I I ca n b e
used in the SMS instruction texts.
If the SMS text contains the % sign, then the following text will be
ignored. Characters %% in the message stop processing the
following text. Using these characters is suitable when sending an
SMS from an internet gateway which adds more text –
advertisements etc. When using the % character it is alw ays
necessary to insert the Master or User code followed by a space
before the command itself.
SMS in struction s can be renamed . Example: It is possible to replace
“AM“ by “LOCK“.
The parameters in bold are factory defaults.
8.3. Dialling-in remote control
Complete remote control by dialling-in from an authorized phone is
possible (see table DIP – para meter E). If you dial the car a larm number
from an authorized phone, it w ill cause a change of state (arming,
di s a rm i n g , e t c . ) . A c a l l t o t h e a l a r m i s f r e e o f c h ar g e ( t he car alarm will not
an s we r t h e i nc o m in g c a ll ) . If operated by dialling- in after an alarm has
been triggered, a slight delay can occur. If disarmed by dia lling-in after
partial arming, th en a subsequent dia lling-in will ca use complete ar ming.
Change of state after d ialling-in can be conf irmed via SMS (opt ional).
8.4. Phone calls by handsfree set (HF-03)
If the HF-03 hands free set is installed, it is possible to receive ca lls
and to dial pre-programmed phone numbers DIAL x. When the
ignition key is on, the remote control (RC-8 x) allows you to operate
the hands free set. The call is done via the car alarm’s SIM, the
handsfree set is not usable for other phones.
Incoming calls – to answer them, press any button on the RC-8x
remote control. By pressing any button aga in, the call will be
terminated.
Calls can be automatically answered, see the HF instruction manual.
Outgoing calls – when the ignition key is on, the RC-8x allows you
to call up to 4 pre-programmed numbers (see chapter 5.1).
When armed, all incoming calls are automatically rejected. If the car
is immobilized or after an alarm has been triggered all calls are
automatically answered (it is possible to listen in).
8.5. Alarm
When an alarm is triggered, the siren will so und for 30 sec., warnin g
SMS messages w ill be sent to all phones (TEL1 to TEL4) an d these
phones will also be ca lled with the siren sound . If automatic lo cation is
turned on, a request for locatio n detection is sent. After the user stops the
alarm, all transmissions are term inated.
To stop the ala rm, disarm th e alarm by pressing the
button on
the remote control or by a disarm SMS instruction (DM). The DM
instruction unlocks the car at the same time. After the alarm has been
stopped by a user in a regular way, an SMS will be sent informing
about alarm termination.
Example of an alarm SMS:
Your car reports: A larm, INP activation, Time 10.12.04 01:4 5
Mercedes repo rts: Alarm, FIRE, gar age sensor acti vation, Time 11.0 2.04 01:12
8.6. Ac o us t ic signalling of arming/disarming
If acoustic signalling is ON (see table 6), the arming is confirmed by
1 beep and disarming by 2 beeps. Partial arming is indicated by two
short beeps. Three beeps while disarming the car indicate that an
alarm was triggered during the armed state. If arming a car with an
active alarm input (e.g. open car boot) arming is supplemented by four
short beeps. The siren will also indicate triggering of a wireless
detector which provides an entrance delay (by a single beep).
9. Editing SMS texts
The SMS texts (alarm information and instructions) are factory pre-
programmed. However, it is possible to change these texts using a
mobile phone or via the www.GSMLink.cz
internet page. This makes
communication convenient for the user.
To change text by mobile phone, send an SMS as below. A single
SMS enables you to specify changes to several texts. Terminate each
text with a comma:
MASTER TXT zz,text,zz,text,…
where: zz is the text index (see following table)
text is your new text – up to 30 characters, full stop (dot)
or comma cannot be used in the text, spaces are
allowed
Example: MASTER TXT 01,LOCK PLEASE
Text numbers 01 to 26 are instructions requiring a MASTER code for
their modification. If you modify these t exts, you change the
instructions which the car alarm will respond to. For example, replacing
“STATUS” with “STATE PASSWORD” will cause that state detection
will be obtainable by “STATE PASSWORD” only. This way you can
insert a “password” into the te xts which prevents misuse. All other
texts are of informational character and corr espond to particular
events, states and input names. This allows you to adjust the names to
a form which suits you well. For example, “INP 1” can be replaced with
“bonnet” etc. Texts can be replaced using the MASTER code as well
as the USER code (optional).
A convenient way for text modification is to use the GSMLink web
page, see paragraph 11.
SMS text table
zz Factory default text zz Fact ory default text
SMS commands: 48 Telephone 4
01 AM 49 Telephone – UC
02 DM 50 Telephone – MC
03 IMO 51 Wireless detector 1
04 UNIMO 52 Wireless detector 2
05 STATUS 53 Wireless detector 3
06 HELP 54 Wireless detector 4
07 CREDIT 55 Wireless detector 5
08 DIAL 56 Wireless detector 6
09 HF 57 Wireless detector 7
10 LOCA TOR 58 Wireless detector 8
11 MC 59 Wireless controller 1
12 UC 60 Wireless controller 2
13 DIP 61 Wireless controller 3
14 TEL 62 Wireless controller 4
15 LEARN 63 Vehicle in move
16 SIREN Status information: