Bedienungsanleitung Jablotron CA-1803BT - reset 2 (Seite 2 von 6) (Englisch)

555038

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

GSM car alarm CA-1803BT „Athos“ 2/6 MHF56704

assign numbers to the names of functions displayed in the phone directory

from the SIM. See table 5.1 for setting the car alarm’s optional parameters.

Settings from the SIM card are read after its insertion and powering up.

 via the Internet page www.GSMLink.cz

which is the most convenient

way. To register there you need the registration code printed on the warranty

card and the master code (factory default is MASTER).

 by sending command SMS messages via a mobile phone, see

table 5.1.

The choice of the correct car alarm mode should be made first. If you

use the car alarm in such a way that it is operated by its original remote

controls (keyfobs), it is necessary to select MODE 2. The settings can

be done by storage in the SIM card (put RESET into the phone directory

as a name and add “2” to the phone number field) or by the SMS

command “MASTER RESET 1” which has to be sent to the car alarm’s

SIM card number. Performing a RESET is indicated by 4 beeps. The

factory default is RESET 0 without any function assigned, except that

the immobilization relay switches on after the ignition key has been

turned on. It is possible to put the car alarm to RESET 0 mode also in

the case, that its functionality should be cancelled entirely.

By carrying out a RESET, you delete all the car alarm settings as well

as all the previously enrolled remote controllers and wireless sensors.

See configuration table 5.1 for performing any subsequent settings.

5. Enrollment of remote controls and detectors

Up to 4 RC-8x remote controls and up to 8 JA-8x wireless detectors can

be enrolled. This mode only allows for the use of remote controls for

operating the HF-03 hands free set. The detectors can be enrolled as either

internal or external. When the car alarm is only partially armed, the detectors

enrolled as internal are excluded from the system (see 8 for operating the car

alarm). The external detectors perform protection for every type of arming.

Steps to enroll RC-8x remote controls:

1. The car alarm should be disarmed, with the ignition on.

2. Send the SMS instruction MASTER LEARN RC

3. The car alarm beeps 3 times and an LED starts to flash.

4. The RC-8x controller is enrolled by pressing buttons

and

simultaneously for approx. 3 sec. A siren chirp confirms the enrollment.

By enrolling the first remote control all other remote controls previously

enrolled will be erased (so enroll all the remote controls intended for use,

one by one).

5. Exit enrollment by turning the ignition off. The alarm confirms the

enrollment by sending an SMS message to authorized phones TEL1 to

TEL4.

Steps to enroll internal detectors:

1. The car alarm should be disarmed, ignition on.

2. To enroll the internal detectors, send the SMS command MASTER

LEARN INT

3. The car alarm beeps 3 times and an LED starts to flash.

4. The detector is enrolled by inserting a battery. By enrolling the first

detector all detectors enrolled as internal will be erased (so, enroll all the

detectors which will be used as internal ones).

5. Exit enrollment by turning the ignition off. The alarm confirms enrollment

by sending an SMS message to authorized phones TEL1 to TEL4.

Steps to enroll external detectors:

1. The car alarm should be disarmed, ignition on.

2. To enroll the external detectors, send the SMS command MASTER

LEARN EXT

3. The car alarm beeps 3 times and an LED starts to flash.

4. The detector is enrolled by inserting a battery. By enrolling the first

detector all detectors enrolled as external will be erased (therefore, enroll

all the detectors which will be used as external ones).

5. Exit enrollment by turning the ignition off. The alarm confirms enrollment

by sending an SMS message to authorized phones TEL1 to TEL4.

If a detector is switched to delay mode, the alarm will provide a 20 second

entrance delay after the detector has been triggered. An exit delay of 20

seconds is provided to all enrolled detectors after the car alarm has been

armed.

If a sensor has been enrolled as an internal one, it can be re-enrolled as

an external one by its enrollment to the desired group.

If a group of detectors should be erased, take the same steps as with

enrollment, except that a “0“ should be added to the instruction (e.g. “LEARN

INT 0“). This starts enrollment and erases previously enrolled detectors. If no

new detectors should be enrolled, only turn the ignition off.

In the case of a low battery in any enrolled detectors a SMS report will be

sent to the first phone number stored in the car alarm’s memory.

Fig. 1: Wiring the alarm in RESET 2 mode. Wiring the alarm this way makes it possible to control the car’s central locking.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron CA-1803BT - reset 2 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron CA-1803BT - reset 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info