GSM pager CA-1803BT „Athos“ 4/6 MHF56803
S
in the SMS instruction texts.
If the SMS text contains the % sign, then the fo
ignored. Characters %% in the message stop processing the
following text. Using these characters is suitable when sending a
SMS from an internet gateway which adds more text
advertisements etc. When using the % character it is always
necessary to insert the Master or User code followed by a space
before the command itself.
SMS instructions
“IMO“ by “BLOCK“.
The parameters in bold are factory defaults.
8.1. Phone calls by handsfree s
If the HF-03 hands free set is installed, it is possible to receive calls
and to dial pre-programmed phone numbers DIA ignition
key is on, an RC-8x allows you to operate the ha
of +12V is required on the ignition key input when a call starts or ends.
The call is done via the car alarm’s SIM, the handsfree set is not usable
for other phones.
Incoming calls – to a
remote control. By pressing any button again, the call will be terminated.
Calls can be automatically answered, see the HF instruction manual.
Outgoing calls – when the ignition key is on (i.e. when a voltage of
+12V is present on its input), the RC-8x allows you to c
programmed numbers (see the
If the ignition key is off (i.
incoming calls are automatically
automatically
8.2. Alarm
When an alarm is triggered
warning SMS messages w
Subsequently, these ph
automatic location
The LED indicates the alar
subsequently
To stopdisarm the alarm b
button on the
remote control.
Example of an alarm SMS:
Your car reports: A
9. Editing SMS texts
The SMS texts (alarm information and instructions) are factory pre-
programmed. However, it is possible to change these texts using a
mobile phone or via the www.GSMLink.cz
internet page. This makes
communication convenient for the user.
To change text by mobile phone, send an SMS as below. A single
SMS enables you to specify changes to several texts. Terminate each
text with a comma:
MASTER TXT zz,text,zz,text,…
where: zz is the text index (see following table)
text is your new text – up to 30 characters, full stop (dot) or
comma cannot be used in the text, spaces are allowed
Example: MASTER TXT 03,BLOCK PLEASE
Text numbers 01 to 26 are instructions requiring a MASTER code for
their modification. If you modify these texts, you c
which the GSM pager will respond to. For example, replacing “STATUS”
with “STATE PASSWORD” will cause state detection to be only
obtainable by “STATE PASSWORD”. This way you can insert
“password” into the texts which prevents misuse. All other texts are of
informational character and correspond to particular events, states and
input names. This allows you to adjust the names
you well. For example, “INP 1” c
can be replaced using the MASTER code as well as the USER code
(optional).
A convenient way for text modification is to use the GSMLink web
page, see paragraph 11. (11)
SMS text table
zz Factory default text zz Fact
SMS commands: 48 Telephone
01 AM 49 Telephone
02 DM 50 Telephone
03 IMO 51 Wireless detector 1
04 UNIMO 52 Wireless detector 2
05 STATUS 53 Wireless detector 3
06 HELP 54 Wireless detector 4
07 CREDIT 55 Wireless detector 5
08 DIAL 56 Wireless detector 6
09 HF 57 Wireless detector 7
10 LOCATOR 58 Wireless detector 8
11 MC 59 Wireless controller 1
12 UC 60 Wireless controller 2
13 DIP 61 Wireless controller 3
14 TEL 62 Wireless controller 4
15 LEARN 63 Vehicle in move
16 SIREN Status information:
17 SET 64 Car
18 AUXA 65 Status:
19 AUXB 66 Armed
20 GPS 67 Disarmed
21 TIME 68 Ignition
25 ON 69 Ignition
26 OFF 70 Engine is blocked
Even 71 Engine is unblocked
30 Alarm 72 No
31 Alarm 73 Alarm timeout
32 Fire 74 Low battery voltage
33 Tamper 75 Power
34 Disarming 76 Power
35 Arming 77 Time
36 Lo 78 Low back-up battery voltage
37 Engine is blocked 79 Partially
38 Engine is unblocked 80 Location
Source:
Confirmati
40 Ignition 81 Command accepted
41 Door contact 82 Command syntax error
42 INP1 activation 83 New MC code:
43 INP2 activation 84 New UC code:
44 Lo 85 Reset
45 Telephone 1 86 Registered phone number:
46 Telephone 87 Credit:
47 Telephone 3 88 LEARN mode, enrolled
The grey-tinted items are not available for RESET 3 mode. Use only
ASCII character set during the text edition.
10. Functions related to GPS
An integrated GPS (Global Position S
provide information about car location with a high
can be obtained upon an SMS re
page. A service for regularly sent location information is also available.
The car alarm is capable of recording all the car’s locations into internal
memory while the car is being used (optional).
Records can be used for statistics about car use (route listing etc.).
The information is also partially available via the GSMLink internet page.
Fully-fledged use is possible using a special service only. In that case, a
central monitoring station is required with information being automatically
downloaded. For more information, consult the m
http://www.jablotron.com/
web page.
10.1. Location detection using GPS
Using a GPS instruction, you can instantly detect the car’s location.
The car alarm responds with the coordinates of the latest known
location. If the current location is not available at the time of reception of
the instruction, or if the car alarm does not chang
a while, the latest location stored in internal memory is sent. Therefore,
messages are supplemented with GMT (Green
value corresponds to the time of detection related to the prime meridian.
In addition, information about altitude, velocity and local time of the GSM
network is provided. Information about location can be sent automatically
after an alarm has been triggered (see the DIP s
An example of an instruction sent from an authori
An example of response: Car alarm reports: Locati
50*43.495N;15*11.253E;515;50, Time:3.12.05 11:35
(GMT:3.12.10:35) Greenwich Mean Time (prime mer
50*43.495N;15*11.253E latitude and longitude
515 altitude (approximated)
50 current
TimeCas:3.12.05 11:35 current local time
