554977
3
Zoom out
Zoom in
Vorherige Seite
1/4
Nächste Seite
CA-340 modular car alarm 3/4 VAV50204
Connection without a CAN-Bus converter,
controlling with RC-8x remote controls
Connection pursuant to Fig 1, setting pursuant to profile 1. The values
shown in the table in bold letters are the default ones The profile is defined by
parameter 1 setting.
A description of individual wire functions is available on page 2.
Vehicle status information is obtained via direct connection to the ignition
circuit and door, bonnet and boot switches. A thus connected car alarm can
control the central locking of the vehicle. It is possible to set an extended
locking impulse which can be used to close the windows of certain vehicle
types after arming.
Connection with a CAN-Bus converter,
controlling with RC-8x remote controls
Setting pursuant to profile 1.
Information about the vehicle status (ignition key, door, bonnet, boot) is
obtained via a CAN-Bus converter.
NOTE: The converter cannot be used to control the central locking of the
vehicle.
Direction indicator (flasher) connection
Optical signaling of arming, disarming and alarm is possible in three modes.
Direct connection to the light bulb circuits. Connection pursuant to Fig. 1.
The power supply is directed to the relay contact via a 15A fuse. The contact
output is forked using diodes and it is then connected to the left and right
direction indicator light.
Connection via a warning light switch, pursuant to Fig. 2. When this
option is selected, the INP1 input always has a feedback function (counting
the flashes) and it has to be connected to a direction indicator light power
circuit. It is therefore not possible to use this optical signaling when the alarm
is controlled with the original remote control without using a CAN-Bus
converter (this option is superior to the setting parameter 12 of profile 2, INP1
then has no function for confirmation of disarming or alarm input). The
flashing can then be controlled with the following options:
„switch“ – the relay is switched if the direction indicator lights
should flash
„button“ - the relay gives an impulse to begin and finish flashing
Profile 1 – controls the central locking
parameter
= LED on
= LED off
1
Central lock
control
Yes, ULK and LCK wires control the locks in the
vehicle
(this setting defines the function of parameters
12,13,14)
2
Rearm
Yes
No
3
Autoimo
Yes
No
4
Disarming with the
Valet button
Yes
No
5
Acoustic signaling
Yes
Partial
6
Increased volume
of signaling
Yes
No
7
Open door test
Yes
No
8
Voltage detector
Yes
No
9
Shock warning
Yes
No
10
Shock alarm
Yes
No
11
AUX output
function
EXT detector power
supply
AUX bus output
12
CL input length
0,5 sec
4 sec
13
Extended lock
impulse length
Yes ( 60 sec.)
No (length pursuant
to parameter 12 )
14
DOOR input
activation
Ground
Ground disconnection
15
INP2 input
activation
Ground
Ground disconnection
16
INP2 input
reaction
Alarm
warning
17
18
BLK output
function
Boot
control
Direct
direction
indicator
control
Direction
indicator
control
switch
Direction
indicator
control
button
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Jablotron CA-340 Nestor wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info