Bedienungsanleitung Jablotron GD-06 (Seite 2 von 5) (Englisch)

554883

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

GSM communicator GD-06 Allegro – complete manual 2/5 MHG 51203

• From a GSM phone, you can send an SMS instruction to switch on

or off the P5 and P6 outputs (example: “ON P5”, “OFF P6”).

• You can also switch the relay on or off by making a phone call to

the GD-06 from a phone registered to TEL1 or TEL2 memory

positions. The GD-06 ALLEGRO doesn’t answer this call, so you

are not charged any telecommunication fee for this remote control.

Notes:

1. You can remotely control the GD-06 from any phone: not only from

the ones stored in the memory TEL1-TEL8. You must just add the

master (default MASTER) or a user (default USER) access code in

front of the instruction.

Example: “MASTER ON P5”

2. The SMS instruction texts are case insensitive. This means that

the instruction “ON P5” is equal to “on p5”.

2.4. Access codes MASTER - USER

Parameter settings:

You can set the communicator without using the MASTER access code

if the jumper MASTER is in the NO MASTER position. If it is in the

MASTER position, then a valid MASTER code must be used. (see

figure 1)

For quick installation it is recommended to set the jumper to the NO

MASTER position. However, for security reasons, during normal

operation the jumper should stay in the MASTER position

3. Advanced setting

General rules for following SMS setting sequences:

1. Jumper is in the MASTER position (it means that the MASTER

code is required)

2. Setting sequences are not case sensitive.

3. Key words must be separated with a space

4. In the examples are used the SMS text, which will be set after the

RESET EN (factory default setting).

5. There can be multiple commands in one SMS, which must be

separated with comma and a blank space.

3.1. Setting of inputs INP

Terminals P1 to P6 can be programmed as inputs. A single SMS

must be always used to program the input, desired parameters as

well as the corresponding phone numbers. If it is necessary to

reprogram the input (for example to add another phone number), all

previously set parameters must be in a new programming SMS sent

again.

MASTER PX INP TYz TYz

Where:

X is the number of terminal P1 – P6

Y is the position of the phone number to which the SMS will be

sent

Z + , – or nothing, depending on the required function

Setting of inputs

Parameter Description

P1, P2, … P6

The name of the terminal which will be programmed as

input via SMS*

INP Parameter for programming a terminal as an input

T1, T2, ….T8 Phone numbers (TEL1 to TEL8)

+ Activation (connecting to GND) will cause sending SMS

Deactivation (disconnecting from GND) will cause

sending SMS

Without + or – parameters the SMS will be sent in case

of any change of input (connecting/disconnecting

to/from GND)

DEL

All previous settings will be erased. No confirmation

SMS will be sent.

* Description of terminal can be changed, but P1, P2 etc, must be

always used in the setting sequences.

tab. 2

Examples of setting SMS:

MASTER P1 INP T2 T3

- Terminal P1 will be set as an input, message about any change of

the input will be sent to TEL2 and TEL3

MASTER P3 INP T4+ T7 T8-

- Terminal P3 will be set as an input, TEL4 will be notified on

activation, TEL8 on deactivation and TEL7 will be notified on all

changes of the input.

MASTER P6 DEL

- All previous settings for terminal P6 will be deleted. The terminal will

be programmed as an input, information about the change will not be

sent to any phone number

Note:

The input signals shorter than 200ms (factory default) will be ignored.

The input filter can be adjusted from 50ms up to 20 seconds.

There are analog inputs, which have adjustable level of their activation

and deactivation (hysteresis). They can also be used for measuring of

analog values (voltage).

Both settings can only be changed via GSMLINK web page. Factory

default setting will be automatically restored after reset.

3.2. Setting of outputs OUT

Relay (NO,C,NC) is always output, terminals P1 to P6 can be

programmed as outputs. A single SMS must be always used to

program the output, desired parameters as well as the

corresponding phone numbers. If it is necessary to reprogram the

output (for example to add another phone number), all previously set

parameters must be in the programming SMS sent again.

MASTER PX OUT parameters or for output relay:

MASTER RELAY parameters

Where:

X is number of terminal P1 – P6

RELAY is the relay output

Parameters parameters according to table 3

Setting of outputs

Parameter Description

P1, P2, … P6

RELAY

The name of the terminal, which will be programmed

as output via SMS*

OUT Parameter for programming a terminal as an output

T1, T2, ….T8

ALL

Phone numbers TEL1 to TEL8, from which will be an

output terminal switched on or off when dialling in

- the output will be controlled by a phone call from all

saved phone numbers

INT

s,m,h

Activation of the output for the preset period of time –

after dialling-in or DTMF code

- duration is programmed by number (selectable from

1 to 99) and unit s-second, m-minutes, h-hours

NEG

Negation of the output status – after dialling-in or

DTMF code

DTMF

To set the controlling DTMF code. The output will be

controlled when the correct DTMF code from the

telephone keyboard of the phone, which is calling to

the Allegro, is received. It is important to enter DTMF

codes without any repetition in their sequencing. For

example If there is code 123, it is not possible to use

another code 12345 - after receiving the initial 123 it

is recognized as the correct code, the command will

be performed and 4 will be considered as the

beginning of a new code.

Figures 0, 1, … 9,*,# can be used; (up to 10 digits)

TEMP

To set a temperature switch – if the temperature drops

below the preset level (set in °C) the output will be

switched on. Hysteresis is 0,5 °C

(hysteresis is adjustable only via www.gsmlink.cz

)

DEL

All previous settings will be erased. No confirmation

SMS will be sent.

* Description of position can be changed, but P1, P2 etc, must always

be used when programming setting sequences.

tab. 3

Jablotron GD-06 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron GD-06

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info