Bedienungsanleitung Jablotron GD-06 (Seite 5 von 5) (Englisch)

554883

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

GSM communicator GD-06 Allegro – complete manual 5/5 MHG 51203

Note:

Date and time in the confirmation SMS sent by GD-06 is taken from the

internal clock built-in to GD-06. This clock is set automatically by any

incoming SMS message. If the GD-06 is disconnected from power the

internal clock will be reset and it is necessary to set them again by

sending any SMS message to the GD-06.

5. Operation

5.1. Operating of outputs via SMS

Terminal must be set to OUT (see 3.2.). The output can be switched

on, switched off or switched on for adjusted period of time (PULSE).

USER (MASTER) code is required if the command SMS is sent from

phone which is not saved in the Allegro’s memory (TEL1 to TEL8).

There can be multiple commands in a single SMS but they must be

separated by comma and blank space No password is required if the

jumper is in the “NO MASTER” position. (see figure 1)

USER COMMAND PARAMETER OUTPUT

Where:

USER (MASTER) user or master code – it is not required if SMS is

received from phone number saved in positions T1 to

COMMAND command (switch on, switch off, pulse)

PARAMETER only for PULSE

(1 to 99 and unit: s seconds; m minutes; h hours)

OUTPUT P1 to P6 or RELAY

Texts of command SMS after RESET EN

Index Parameters Meaning - description

100 ON To switch the output on

101 OFF to switch the output off

102 PULSE To switch the output on for adjusted period of

time

103 CREDIT To find out level of credit of pre-paid card

104 LEVEL To find out current level of GSM signal

105 CALL To get a reverse call for monitoring the area

via HF-03 set

106 STATUS To learn status of the device

107 ENABLE To enable sending of automatic reports

messages

108 DISABLE To disable sending of the automatic reports

messages (for example during installation)

109 USER User code – is used for operation from

phones which are not stored in the memory

(TEL1-TEL8)

110 MASTER Master code – is used for programming or for

operation from phones which are not stored in

the memory (TEL1-TEL8)

DINFO Information about registration code, hardware

and software version

Description of all commands is editable to simplify the operation of

Allegro (see 3.4.)

tab. 6

Examples of operating SMS:

ON P1

- Output P1 will be switched on

ON HEATER

- Output named HEATER will be switched on

USER OFF LIGHT

- Output named LIGHT will be switched off by SMS from phone, which

is not saved in Allegro (T1 to T8)

MASTER SET ON LIGHT

- Output named LIGHT will be switched on by SMS from phone, which

is not saved in Allegro (T1 to T8)

PULSE 20m P1

- Output P1 will be switched on for 20 minutes

ON HEATER, OFF LIGHT, PULSE 20m P1

- Multiple commands in one SMS

5.2. Operating of outputs by dialing-in

Outputs can be operated by phone calls from preset phone numbers

(T1 to T8). Reaction to a phone call will result in change of status (on,

off, on..) of an output or its triggering for a selected period of time.

Output must be programmed for this function by parameter NEG or INT.

Phone call must be made from phone number programmed into the

Allegro (tab.3). Multiple outputs can react independently to one phone

call, depending on their settings. The GD-06 doesn’t answer this call, so

you are not charged any telecommunication fee for this remote control.

5.3. Operating of outputs by DTMF code

It is possible to operate the outputs by DTMF code inserted when an

incoming call is answered by the Allegro. These DTMF codes must be

programmed by parameters NEG, INT and DTMF (tab.3). The phone

call will be answered within the selected time, programmed by

parameter “T” in sequence HF (4.1.). Factory default time is 10

seconds. After that Allegro is ready to receive DTMF code. Accepted

code is confirmed by a long beep. It is also important to remember that

if the phone number which is being used for entering DTMF code has

also been programmed to control an output by dial-in, then the

programmed output will be actually operated before the call can be

answered or a DTMF can be inserted.

5.4. Operating of special functions

MASTER (USER) STATUS

This command is used for checking the status of the device. The

device will send the actual status back to the sender’s number.

Communicator GD-06 reports: 1.1.04 0:00:34 Status: P1 Off, P2 Off,

P3 10.6V, P4 Off, P5 Off, P6 Off, RELAY Off, 22.5C, GSM level signal 8

MASTER (USER) CALL

- Device will make a phone call back to the number of the command

sender to activate the monitoring mode – communicate (listening)

with the area via HF-03 hands-free set. (It is necessary to have HF

set connected).

MASTER (USER) DISABLE

MASTER (USER) ENABLE

This command is used to disable or enable all automatic reports from

the system (SMS, SMS+, GPRS, voice calls). It is especially useful for

disabling of sending automatic reports during installation or servicing.

MASTER (USER) LEVEL

This command reports the strength of the GSM signal, the result will

be sent as an answer to the sender’s number.

MASTER (USER) CREDIT

An SMS containing the word CREDIT will result in sending of the

information about the actual level of credit of pre-paid card. (see 4.2.)

MASTER (USER) DINFO

Device will report to the requesting number its version of hardware

and firmware as well as its code for registration to the www server

www.gsmlink.cz.

6. Web server remote access

The setting server allows a user to read and change configuration of the

Allegro. Data transfer is made by sending an SMS or GRPS. The web

site allows:

• Check current status of device

• Operate the output terminals

• Program all setting, which can be also set via SMS messages

• Program additional features

• Edit SMS texts (only if GPRS data transfer is used)

The quantity of data sent by SMS is optimized to reduce costs as

much as possible. GPRS data transfer can be used, but must be

activated on the SIM card and proper APN must be set (4.5.).

6.1. Registration to the web site

Web site www.gsmlink.cz – to register your system use the

registration code printed in the warranty certificate (the code has a form

xxxx-xxxxx-xxxx and it is a unique for each device) the registration code

can be also obtain by sending

SMS to GD-06 “MASTER

(USER) DINFO”.

Jablotron GD-06 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron GD-06

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info