555052
8
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
H-915 installation manual 11/8 TBT502 01
x=0 Technical alarm - results when the a.c. power is off for a long time and the backup battery is nearly discharged. Any
combination of outputs can be selected for this kind of alarm (y can be from 0 to 7)
x=1 Fire alarm - triggered by a fire loop. This alarm always activates the FIRE output. But it can also activate any
combination of other outputs (y can be from 0 to 7)
x=2 Intruder alarm - is triggered by any intruder zone (see zone definition) or if a predetermined number of attempts to
enter a valid access code is reached . Any combination of outputs can be selected for this kind of alarm (y can be from 0
to 7).
x=3 Panic alarm - is triggered by the panic code, by any silent loop (24Hr. silent loop, 24Hr. delay silent loop etc). This
alarm always activates the PANIC output. It can also activate a relay output if necessary. The "y" can only be 0 (panic
output only) or 2 (panic output and relay output).
There are three programmable alarm outputs in the control panel:
External Siren (E.S), Relay, Internal Siren (I.S.). Consider, that +BS output works the same way as a relay output.
Therefore, if the relay is activated, the +BS output is activated as well. See the following table to set requested
combination of output's reaction:
y E.S. Relay I.S.
0 off off off
1 on off off
2 off on off
3 on on off
4 off off on
5 on off on
6 off on on
7 on on on
Note: the panic output is always activated by the panic alarm and the fire output is always activated by the fire alarm.
Examples: Enter [3] [11] so that fire alarm will activate the fire output and the external siren. Enter [3] [32]so that panic
alarm will activate the panic output and relay. Enter [3] [27] so that the intruder alarm will activate all programmable
outputs.
[4] [xy] System option function definition - once this section is entered, two digits are required. The first
digit determines what function you want to program. The second digit sets the function.
There are six optional functions available:
[4] [0y] A Chirp sound confirmation of arming (one chirp for arming, two chirps for disarming and three chirps for
disarming when alarm memory is present). If y=0, then the arming control is confirmed only by the keypad's buzzer. If
y=1, then the arming is confirmed by the internal siren as well. If y=2, then arming is confirmed by the external siren and if
y=3, the arming is confirmed by both sirens. The "y" can only be from 0 to 3.
[4] [1y] External arming control with loop 6 input. If y=0, zone input 6 will work as programmed in section [1]. If y=1,
than zone input works as input for external arming and disarming. If you close this input with E.O.L. resistor for
a moment, it will have the same function as entering of a valid access code. By doing this, the control panel can be
armed/disarmed by another device (hidden push-button, wireless remote control UC-200, digital keypad KB-1050 etc.). A
corresponding zone LED has the opposite function if external arming control is enabled (the LED is off when the input is
unbalanced).
Note: If external arming control input is enabled, zone 6 will not work as programmed in section [1].
[4] [2y] Number of attempts to enter a valid access code before the intruder alarm is triggered. The "y" can only be
from 0 to 9. If zero is selected, there is no limit to the number of attempts.
[4] [3y] Quick arming function. If y=0, the quick arming is disabled, if y=1, the quick arming is enabled (see [][0] and
[][9] commands description).
[4] [4y] Auto AT HOME arming. If y=0, the control panel can be AT HOME armed only by the [][9] command. If y=1,
auto AT HOME arming is enabled. The system is able to recognize automatically if you stay at home or not. If a correct
access code is entered for arming, the green ARM LED will flash slowly . The system expects that you will stay home and
it is ready for AT HOME arming after exit delay. If you trigger a delay zone during the exit delay (for example with
magnetic sensor on the exit/entrance door), the light of the ARM LED turns to yellow and the system will be fully armed.
The [][9] command can also be used for immediate AT HOME arming.
[4] [5y] Silent alarm if somebody in. If y=0, then alarm outputs can work as programmed in [3] Alarm outputs definition.
If y=1, then relay and internal siren outputs are disabled if any alarm triggered when disarmed or AT HOME armed (sb. is
present).
Examples: Enter [4][01] to program chirp sounds with internal sirens for arming confirmation, enter [4][41] to enable auto
AT HOME arming function,.....
[5] [xy] Testing of the system outputs. Once this section is entered two digits are required.
The first digit (x) determines if you want to test the control panel or devices which are connected on serial line (keypad
terminals). If x=0, you can test the control panel outputs. If x=1, an optional device, connected to a serial line can be
connected (future use). The second digit (y) determines which control panel output will be activated. For x=0 you can
use the following y (from 0 to 5):
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Jablotron H-915 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info