Installation manual: Oasis security system JA-80K - 2 - MKE51801
Contents:
1. CONTROL PANEL ARCHITECTURE..................................................3
1.1. OPTIONAL SYSTEM CONFIGURATIONS ...............................................4
2. INSTALLATION...................................................................................4
2.1. POWER INLET ................................................................................4
3. CONTROL PANEL MEMORY UNIT ....................................................4
4. CONTROL PANEL CONNECTORS AND TERMINALS......................4
5. WIRED KEYPAD CONNECTION.........................................................5
6. BACK-UP BATTERY...........................................................................5
7. POWERING-UP THE CONTROL PANEL FOR THE FIRST TIME.......6
7.1. W
IRELESS KEYPAD ENROLLMENT .....................................................6
8. LANGUAGE SELECTION OF THE KEYPAD......................................6
9. RESETTING THE CONTROL PANEL .................................................6
10. CLOSING THE CONTROL PANEL COVER ...................................6
11. ENROLLING WIRELESS DEVICES................................................6
11.1. I
NSTALLING WIRELESS DEVICES .......................................................6
11.2. E
NROLLING WIRELESS DEVICES TO THE CONTROL PANEL ....................6
11.3. T
ESTING ENROLLED DEVICES........................................................... 7
11.4. MEASURING SIGNAL STRENGTH ....................................................... 7
11.5. E
RASING ENROLLED DEVICES ..........................................................7
11.6. ENROLLING THE CONTROL PANEL TO UC AND AC MODULES ............... 7
12. CONTROL PANEL PROGRAMMING .............................................8
12.1. CONTROL PANEL PROGRAMMING SEQUENCES ...................................8
12.2. EXIT DELAY TIME ..........................................................................10
12.3. E
NTRANCE DELAY TIME .................................................................10
12.4. A
LARM DURATION TIME .................................................................11
12.5. PGX AND PGY FUNCTIONS........................................................... 11
12.6. CHANGING TELEPHONE NUMBERS IN MAINTENANCE MODE................. 11
12.7. RADIO INTERFERENCE INDICATION .................................................11
12.8. RADIO COMMUNICATIONS SUPERVISION .......................................... 11
12.9. RESET ENABLED ........................................................................ 11
12.10. ENROLLMENT TO A SUB CONTROL PANEL FOR SETTING (ARMING)
CONTROL
11
12.11. MASTER CODE RESET .............................................................. 12
12.12. CONTROL PANEL ENROLLMENT TO UC OR AC MODULES OR TO A SUB
CONTROL PANEL
12
12.13. SETTING (ARMING) WITHOUT AN ACCESS CODE........................... 12
12.14. TRIGGERED-DETECTOR INDICATION ...........................................12
12.15. C
ONFIRMATION OF INTRUDER ALARMS ....................................... 12
12.16. EXIT DELAY BEEPS................................................................... 12
12.17. EXIT DELAY BEEPS WHILE PARTIALLY SETTING (ARMING) ..............13
12.18. ENTRANCE DELAY BEEPS.......................................................... 13
12.19. SETTING (ARMING) CONFIRMATION BY WIRED-SIREN CHIRP........... 13
12.20. SIRENS ALWAYS SOUND DURING AUDIBLE ALARMS .......................13
12.21. WIRELESS SIREN ALARM ENABLED (IW AND EW) ........................ 13
12.22. A
UTO-BYPASS USER APPROVAL VIA THE KEY ........................... 13
12.23. F
INAL-DOOR DETECTORS..........................................................13
12.24. P
ARTIAL SETTING (ARMING) OR SYSTEM SPLITTING ...................... 14
12.25. AUTOMATIC SUMMER TIME (DAYLIGHT SAVING TIME) .................... 14
12.26. T
AMPER ALARM IN RESPONSE TO AN INCREASE IN THE NUMBER OF
TRIGGERED TAMPER SENSORS
............................................................................. 14
12.27. O
PERATING THE PG OUTPUTS USING 8 AND 9 .......................14
12.28. P
ERMANENT ALARM STATUS DISPLAY FOR A SET SYSTEM .............14
12.29. T
AMPER ALARM IF UNSET.......................................................... 15
12.30. E
NGINEER RESET .................................................................... 15
12.31. R
ECORDING PG OUTPUT ACTIVATION TO MEMORY ...................... 15
12.32. ANNUAL CHECK NOTIFICATION................................................... 15
12.33. O
NLY SINGLE ALARM INDICATION ...............................................15
12.34. S
ETTING (ARMING) BY SERVICE CODE ........................................ 15
12.35. A
UDIBLE PANIC ALARM ............................................................. 15
12.36. HIGHER CONTROL-PANEL RECEIVER-SENSITIVITY ........................ 15
12.37. ACCESS BY CODE PLUS CARD ................................................... 16
12.38. AUDIBLE 24 HOUR INTRUDER ALARM ..........................................16
12.39. SERVICE MODE ONLY WITH SERVICE CODE AND MASTER CODE ......16
12.40. D
EVICE REACTIONS AND SECTION ASSIGNMENT........................... 16
12.41. CODE/CARD REACTIONS AND SECTION ASSIGNMENT ....................17
12.42. ENROLLMENT BY KEYING IN PRODUCTION CODES ........................ 17
12.43. AUTOMATIC SETTING/UNSETTING SCHEDULE............................... 17
12.44. CHANGING THE SERVICE CODE..................................................17
12.45. G
O TO MAINTENANCE MODE...................................................... 17
12.46. S
ETTING THE INTERNAL CLOCK.................................................. 17
12.47. EDITING KEYPAD TEXT.............................................................. 18
13. OPERATING THE SYSTEM..........................................................18
13.1. THE SYSTEM KEYPAD.................................................................... 18
13.1.1. Keypad indicators:............................................................ 18
13.1.2. LCD display...................................................................... 18
13.1.3. Keypad display sleep-mode ............................................. 18
13.1.4. Keys.................................................................................18
13.1.5. Functions beginning with the key ...............................19
13.2. P
ROGRAMMING ACCESS CODES AND CARDS ....................................19
13.2.1. Programming access codes and cards.............................19
13.3. S
ETTING AND UNSETTING (ARMING/DISARMING) THE SYSTEM ............ 20
13.4. MAINTENANCE MODE ...................................................................20
13.4.1. Displaying which user/card positions are occupied...........20
13.4.2. Bypassing devices............................................................20
13.4.3. Protecting a car near the system ......................................20
14. OPERATING AND PROGRAMMING THE SYSTEM BY PC........21
15. BASIC GUIDANCE FOR INSTALLERS........................................21
16. TROUBLE-SHOOTING..................................................................22
17. CONTROL PANEL TECHNICAL SPECIFICATIONS ....................22
