Bedienungsanleitung Jablotron JA-80V - LAN Communicator (Seite 10 von 10) (Englisch)

631259

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

The JA-80V LAN/PSTN line communicator - 10 - MKA51202

7.2. The communicator’s LEDs

Green LED:

 regular flashing – communication in progress (ARC, SMS or

remote access)

 off – data is waiting to be sent to an ARC

 lit permanently – no waiting data to be sent to an ARC

Red LED:

 off – communication to the ARC is OK

 lit permanently – impossible to send data to any ARC

Yellow LED:

 regular flashing – Ethernet connected, DHCP is not working

 off – Ethernet is not connected

 lit permanently – Ethernet connected and communication with

the network is OK

7.3. After entering service mode the communicator:

• finishes reporting to ARCs (if any is needed)

• unfinished SMS and call reports are cancelled

• unsent ARC reports are only erased if ARC tel. numbers / IP

addresses or the ARC communication format or the installation ID are

changed

• alarm restoration reports or fault restoration reports are sent to the

ARC even in service mode

• changes to communicator settings do not take effect until service

mode has been exited

7.4. Configuring the communicator in maintenance mode

If configuring the communicator in maintenance mode is enabled (via

control panel programming), then the above described programming

sequences can be used to set:

• tel. numbers M1 to M7

• the events reported by SMS and phone calls

7.5. Remote access by Internet

The system can be accessed remotely via www.GSMLink.cz

which

allows complete programming by installers and also operating the

system by end users. To access the system remotely it is necessary

to:

• Have the communicator connected to an Ethernet network which

allows access to www.GSMLink.cz

• Register the communicator via the GSMLink web page by:

o displaying www.GSMLink.cz and selecting New registration

o setting your login details (name and password)

o entering the communicator registration code (see the

communicator label)

o entering your system access code (user or service – this gives

you access to the user menu or the installer menu accordingly)

o after entering the above parameters it should be possible to

establish a connection with the system.

If your communicator is using a dynamic IP address when

communicating with the GSMLink server, then it could be that you

will have to wait for a connection (if your IP address has been

changed). GSMLink will indicate how long it will take to get

connection with the system. To shorten the waiting time it is

possible to initialise the communication remotely by dialling from a

telephone which has been programmed for this function (see

5.10.1).

• for further access sessions you only need to enter your login details

(these can be memorized by your web browser)

• several people can register for internet access to the system (both

installers and users)

• A service technician needs only one set of login details to access

various installations. After the first system has been registered, the

installer can add (or remove) other installations to(or from) his/her

GSMLink account.

• there is a demo version of remote access on www.GSMLink.cz

• using www.GSMLink.cz

is free of charge

7.6. A complete list of CID reports to ARCs

A report to an ARC consists of: installation ID, event code, subsystem

number and the number of the source (device or code). In IP CID and

SMS CID, in addition to this, a time stamp is also sent as follows.

List of the CID reports

CID code Event ec

1130 / 3130 Intruder alarm – instant / restored 1 / 9

1134 / 3134 Intruder alarm – delayed / restored 2 / 9

1110 / 3110 Fire alarm / restored 3 / 9

1120 / 3120 Panic alarm / restored 4 / 9

1461 / 3461 Number of incorrect code-entries exceeded

alarm / restored

5 / 9

1140 / 3140 Alarm triggered during control panel power-up /

restored

6 / 9

1137 / 3137 Tamper alarm / no tampering 7 / 8

1144 / 3144 Device tamper alarm / no tampering 7 / 8

1406 Alarm cancelled by user 10

1401 / 3401 Unsetting / setting 12 / 11

3402 Partial setting 13

3408 Codeless complete setting 14

1354 / 3354 External communication fault / restored 15 / 16

1300 / 3300 Fault (except device) / all faults restored 17 / 18

1330 / 3330 Device fault / all faults restored 17 / 18

1301 / 3301 Mains dropout longer than 30 minutes /

restored

19, 20 / 21

1302 / 3302 Battery fault (except devices) / all battery faults

restored

22 / 23

1384 / 3384 Device battery fault / all battery faults restored 22 / 23

1306 / 3306 Switching to Service Mode / Leaving Service

mode

24 / 25

1661 / 3661 PGX ON/OFF 26

1662 / 3662 PGY ON/OFF 27

1355 Radio communication jamming present 28

1350 / 3350 Internal communication fault / restored 29 / 30

1602 Communication test 31

1138 Unconfirmed alarm 32

1351 Communication fault to ARC1 to ARC2 if

backups

1393 Annual check request 17

1551 / 3551 Communicator blocked / restored 31 only in

IP CID

List of source numbers

Source

number

Source

701 Control panel

731 Communicator

741 Wired keypad

001 - 050 Devices 01 - 50

500 Master code

599 Service code

501 - 550 Codes 01 - 50

Subsystem: 01 in all reports

In a split system, for setting and unsetting: 02 = A, 03 = B

For partial setting: 02 = A, 03 = AB

8. Technical specifications

Power 12V DC (from the control panel)

Stand-by consumption about 35 mA

Max. consumption (during communication) 1 A

Complies with EN 50131-1/2006, EN 50136-1-1, 2-1 as:

ATS 4 if the ARC comm. repeating period is zero (sequence 06a0)

ATS 5 if ID CID protocol is used and the repeating period is set to zero

(sequence 06a0)

Operating environment ( –10 to 40°C) class II

Safety EN 60950

EMC EN 55022, EN 5030-4

Radio transmissions ETSI EN 301419-1 and EN 301511

CLIP protocol (caller ID + SMS) ETSI EN 300 089 V3.1.1(2000-12)

Jablotron Ltd. hereby declares that the JA-80V is in compliance with

the essential requirements and other relevant provisions of Directive

1999/5/EC.

Jablotron Ltd. hereby declares that the product complies with part 15

of the FCC rules. Operation is subject to the following two

conditions: 1. This device may not cause harmful interference, and 2.

This device must accept any interference received, including

interference that may cause undesired operation.

CAUTION: Changes or modifications no expressly approved by Jablotron could

void the user’s authority to operate the equipment.

The original of the conformity assessment can be found at www.jablotron.com

, -

Technical Support section

Note: Although this product does not contain any harmful materials we

suggest you return the product to the dealer or directly to the producer

after use.

Jablotron JA-80V - LAN Communicator Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info