Bedienungsanleitung Jablotron JA-80Y - GSM communicator (Seite 8 von 12) (Englisch)

631261

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

The JA-80Y GSM communicator - 8 - MFJ55304

where

x = 0 incoming calls are ignored

x = 1 to 8 the communicator will answer after x multiplied

by 5 seconds of ringing (e.g. x=4=20sec.)

x = 9 answers after a second call - first there must be

at least one ring, then a pause (10 to 45sec.) and

then just after the first ring of the second call, the

call will be answered

Factory default setting: 9045 – answers after 25sec. (about 5 rings)

5.11. The simulated phone line function

This sequence defines the function of the phone connected to the

simulated telephone line (if used).

98 y

where Function

y = 0 phone line –for making phone calls. If the # key is

pressed when the receiver is picked up, the phone

will work as an alarm system keypad

y = 1 the phone works as a system keypad, it is

impossible to make phone calls

y = 2 the telephone line is disabled

y = 3 emergency call –automatically calls a pre-

programmed number (see 5.12), just after the

receiver is picked up. Pressing the ∗ key within 2

sec. after having picked up the receiver will switch to

a dial tone and will allow the user to make phone

calls

Note: while the communicator is occupied with reporting events, or it is

not registered to the GSM network, a busy signal is heard on the

connected phone.

Factory default setting: y = 0 = phone line

5.11.1. Using an SMS phone connected to the simulated line

A phone capable of sending and receiving SMS messages by CLIP

protocol can be connected to the simulated phone line. In the phone,

both the TX and RX numbers should be programmed to 1111.

If an SMS message is sent from this phone to the phone number

“001” it will go directly to the communicator (free of charge). This can

be used to send instructions to the system (e.g. text programming

etc.).

If the communicator is programmed to report to phone number 001

the reports will be sent to the attached phone via the simulated line

(free of charge).

If the attached phone provides caller identification (CLIP), then the

caller’s phone number will be shown on the display.

5.12. Emergency telephone number

If the simulated phone line is set to emergency call mode (see 5.11),

then after picking up the receiver the phone will automatically call a

number programmed by:

952 xx...x ∗0

where:

xxx…x is a phone number (max. 20 digits), keying in

∗9 will enter “+” for international calls

To erase the number enter 952∗0

Factory default setting: the emergency number is erased

5.13. GSM signal dropout indication

This selectable feature monitors connectivity with the GSM network. If

enabled, it indicates problems and generates an external

communication fault report if there is a GSM signal dropout longer than

15 minutes.

9210 disabled

9211 enabled

Factory default setting: disabled

5.14. The microphone sensitivity of the phone

The sensitivity of the attached phone (or intercom) can be adjusted by:

953x where x can be from 1 to 9 (max.) – factory default = 5

5.15. The speaker loudness of the phone

The loudness of the attached phone (intercom) can be adjusted by:

954x where x can be from 1 to 9 (max.) – factory default = 5

5.16. Number to be called to maintain SIM card validity

If a prepaid SIM card is used and a lack of outgoing phone calls for a

certain period cancels the validity of the SIM card, then this function

offers the following: if there have been no outgoing phone calls within

the last 90 days, then the communicator automatically calls the

number programmed by this sequence, waits until the call is answered

and then after 10 sec. automatically hangs up.

924 xx...x ∗0 where xx...x = phone number

Notes:

• To erase this number enter 924

∗

• It is recommended to call cheap public services (e.g. weather

forecasts etc.) but not toll-free numbers.

Factory default setting: erased

5.17. Automatic SIM card credit interrogation

The communicator is capable of checking the credit balance of its SIM

card by interrogating the GSM network with an SMS containing a

recognized instruction string (if the network supports this feature).

There are two options: The credit balance can be checked when the

user requests it by sending an SMS instruction to the communicator, or

the communicator can be set to check it regularly itself. To configure

credit balance checking send an SMS in the format:

code_CREDIT_uu..u_xx_yyy_zz

where:

code valid master or service code (e.g. 8080 or 1234)

_ space

uu..u instruction recognized by the GSM network to check the

balance (e.g. ∗101# etc.)

xx automatic checking period in days

yyy minimum acceptable credit balance

zz the textual position in which the number showing the

balance starts in the reply message from the GSM

provider

In addition, a new way of SIM card balance checking is now available

for networks which do not support standard balance checking but

provide SMS reporting after each charged transaction. In this case you

can configure credit interrogation by sending the following SMS:

code_CREDIT_S_xx

where:

code is a valid master or service code (e.g. 8080 or 1234)

_ is a space

S is literally S or s (a distinguishing mark)

xx automatic checking period in days (optional)

Simultaneously, it is necessary to disable SMS forwarding and to

configure the number used to maintain SIM card validity (the SIM

validity-maintenance call number).

After performing the configuration you can check the balance anytime

by sending the CREDIT instruction. By specifying the xx part you also

request the checking to be performed automatically. On each check,

the communicator performs a charged call (to the SIM validity-

maintenance call number), and enables the forwarding of a single

SMS from the network operator to the first pre-programmed number.

Notes:

• If the reported credit balance is lower than the set limit (yyy), the

credit balance message from the provider will be forwarded to phone

numbers M1 and M8 to remind someone to top up the SIM card.

• If event 22 is programmed to be reported to any tel. numbers (M1 to

M8) then the message “Discharged battery of the communicator” will

be sent to these numbers if the credit balance is under the yyy limit.

Jablotron JA-80Y - GSM communicator Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80Y - GSM communicator

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info