Bedienungsanleitung Jablotron JA-80Y - GSM communicator (Seite 10 von 12) (Englisch)

631261

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

The JA-80Y GSM communicator - 10 - MFJ55304

zz..z installation ID number, max. 8 characters (0 to 9 and

∗1=A to ∗6=F - hexadecimal number)

Factory default setting: 0000 for both ARCs

5.26. Selecting the ARC communication protocol

To select the required communication protocol enter:

04 a x

where:

a 1=ARC1, 2=ARC2

x 0=Contact ID, 1=SMS CID, 2=IP CID

Notes:

• IP CID is the fastest of the above protocols and it also allows very

frequent checking of communication reliability with the ARC (e.g.

every 5 minutes)

• Contact ID protocol can be used with ARCs linked by standard

telephone lines (if they support Contact ID)

• If your ARC does not allow SMS CID or IP CID protocols, please

contact a Jablotron distributor for details on how to update your

ARC.

Factory default setting: Contact ID for both ARCs

5.27. Selection of events to report to ARCs

The system recognizes 32 different types of events - see the following

table. This sequence allows you to select which events are reported to

which ARC.

05 a ec x

where a 1 = ARC1, 2 = ARC2

ec event code 01 to 32

x 0 = no report, 1 = report

Factory default setting: all events are reported

ec Event

01 Intruder alarm - instant

02 Intruder alarm - delayed

03 Fire alarm

04 Panic alarm

05 Number of permitted incorrect code-entries

exceeded

06 Alarm triggered during control panel power-up

07 Tamper alarm

08 End of tamper alarm

09 End of alarm indication

10 Alarm cancelled by user

11 Setting

12 Unsetting

13 Partial setting

14 Codeless setting

15 External communication fault

16 External communication restored

17 Fault

18 Fault no longer present

19 Mains dropout longer than 30 minutes

20 Mains dropout

21 Mains restored

22 Discharged battery

23 Battery OK

24 Switching to Service Mode

25 Leaving Service Mode

26 PGX ON/OFF

27 PGY ON/OFF

28 Radio communication jamming present

29 Internal communication fault

30 Internal communication restored

31 Communication test

32 Unconfirmed alarm

Besides the events listed above, the communicator also reports some

events which are not selectable here (e.g. the annual inspection

request if enabled in the control panel = CID 1393)

5.28. Defining the delay before data is resent to an ARC

The communicator tries to send reports to the main number / IP

address, and if unsuccessful it then tries the backup number / IP

address. If still unsuccessful, it then tries to re-send the data to both

the ARCs again as before, but after a period defined by:

06 a x

where

a 1 = ARC1, 2 = ARC2

t is the period: 0=immediately, 1 to 9 = 1 to 9 minutes

Factory default setting: 1 min. for both ARCs

5.29. ARC communication checking period

The time to wait after the last report sent to an ARC before performing

an ARC communication check is set by this sequence. The

communication-checking event code is 31 (see 5.27). This sequence

programs how often the communication check is performed:

07 a hhmm

where

a 1 = ARC1, 2 = ARC2

hh hours

mm minutes

Notes:

• Checking reports are not sent in service mode

• IP CID protocol allows very frequent checking of ARC

communication (e.g. every 5 minutes).

Factory default setting:24 hours after the last report – for both ARCs

5.30. Enable ARC reporting (ARC2 backs up ARC1)

This sequence allows reporting to ARCs to be switched on/off and also

enables ARC2 to backup ARC1:

00 a x

where

a 1=ARC1, 2=ARC2

x 0=off, 1=on, 2= ARC2 backs up ARC1 (2 can only be

entered for ARC2)

Note: if ARC2 backs up ARC1 then it will only receive data if it is not

possible to deliver it to ARC1. A report containing “Communication

fault to ARC1” is then sent to ARC2 together with the first report to

ARC2.

Factory default setting: both ARCs = off

5.31. Recording reports sent to ARCs in the control panel

memory

This sequence enables the recording of every report successfully

communicated to ARCs in the control panel’s internal memory.

080 enabled

081 disabled

Note: it is recommended not to record reports sent to ARCs but to

enable the indication of ARC communication faults (see 5.32). This

saves a significant amount of control panel memory. The system

initially assumes that every report is successfully delivered to ARCs,

but if a report is not successfully delivered within 110 seconds of

transmission, then a communication fault will be indicated and

recorded.

Factory default setting: enabled

5.32. Indicate an ARC communication fault if a report is not

successfully received within 110 sec of transmission

Enables the indication and recording of a communication fault if a

report is not successfully delivered to an ARC within 110 seconds of its

transmission.

090 communication faults not indicated

091 communication faults indicated

Notes:

• The communicator continues trying to send information to an ARC

even after a communication fault has been indicated (after the data

has been delivered, communication fault indication stops).

• For communication-checking reports the delivery time limit

(confirmation from the ARC) is 300 minutes. But if any other report is

sent to the ARC it must be confirmed within 110 seconds (otherwise

a communication fault will be indicated)

Factory default setting: communication faults not indicated

Jablotron JA-80Y - GSM communicator Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80Y - GSM communicator

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info