Bedienungsanleitung JBSystems MCD200 (Seite 4 von 43) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

468050

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

ENGLISH USER MANUAL

JB SYSTEMS® 3/81 MCD200

 In the event of serious operating problems, stop using the appliance and contact your

dealer immediately.

 Please use the original packing when the device is to be transported.

 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.

INSTALLATION GUIDELINES:

 Install the unit in a well-ventilated location where it will not be exposed to high

temperatures or humidity.

 Placing and using the unit for long periods near heat-generating sources such as

amplifiers, spotlights, etc. will affect its performance and may even damage the unit.

 Take care to minimize shocks and vibrations during transport.

 When installed in a booth or flight case, please make sure to have good ventilation to

improve heat evacuation of the unit.

 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding

temperatures when bringing it into a warm room after transport. Condense sometimes

prevents the unit from working at full performance.

CLEANING THE CD-PLAYER:

Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water inside

the unit. Do not use volatile liquids such as benzene or thinner which will damage the unit.

CONNECTIONS

 Use the supplied cinch cable to connect the audio output of the CD player with a CD

input on your mixing unit.

 Also connect the fader start cable if your audio mixer has fader start connections.

(Synq® or Pioneer® compatible)

 Connect the mains cable.

ENGLISH USER MANUAL

JB SYSTEMS® 4/81 MCD200

CONTROLS AND FUNCTIONS

1. SEARCH Button: This button has 4 forward and 4 backward speed positions for

searching through songs. The more you turn the wheel in either direction the faster you

will search through the music.

2. TRACK SEARCH Buttons: These buttons are used to select the track to be played.

Forward skip & back skip.

3. IN/R.CUE button: Allows you to set the cue point without stopping the playback (CUE

ON THE FLY). This button also sets the beginning of a seamless loop. When you play

one of the hot cues(19), the starting point is also copied to this button.

4. OUT/EXIT button: Used to set the endpoint when looping music. The player starts to

loop seamlessly until you press this button again to exit. When a loop is programmed

but not active you can also restart the loop. The point where you press the button will

be memorized as the new end point of the loop. When the player is in “loop edit mode”

pressing this button stops the loop editing and saves the current endpoint of the loop.

5. RELOOP/STUTTER button: This button has 3 functions:

 RELOOP: If a loop is programmed and you have hit the OUT/EXIT button(4), press

the reloop button to enter the loop again. Just press the OUT/EXIT(4) button to exit

the loop. (intro and end points of the loop are unchanged)

 STUTTER: When a loop is playing you can press this button to restart the loop at

once. You can also press this button when a track is not playing in loop. Every time

the RELOOP/STUTTER button is pressed, it will restart the music from the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBSystems MCD200 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info