Bedienungsanleitung Jensen HD5112 (Seite 9 von 32) (Englisch)

509253

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

HD5112

9. Attach one end of the perforated support strap (supplied) to the screw

stud on the rear of the chassis using the hex nut provided. Fasten the

other end of the perforated strap to a secure part of the dashboard

either above or below the radio using the tapping screw and washer

provided. Bend the strap, as necessary, to position it. CAUTION: The

rear of the radio must be supported with the strap to prevent damage to

the dashboard from the weight of the radio or improper operation due to

vibration. The strap also ensures proper electrical grounding of the unit.

10. Re-attach the front panel to the chassis and test radio operation by

referring to the operating instructions for the unit.

NOTE: For proper operation of the CD player, the chassis must be

mounted within 20° of horizontal. Make sure the unit is mounted within

this limitation.

ISO Installation

This unit has threaded holes in the chassis side panels which may be used

with the original factory mounting brackets of some vehicles to mount the

radio to the dashboard. Please consult with your local car stereo shop for

assistance on this type of installation.

1. Remove the existing factory radio from the dashboard or center console

mounting. Save all hardware and brackets as they will be used to mount

the new radio.

2. Carefully unsnap the plastic frame from the front of the new radio

chassis. Remove and discard the frame.

3. Remove the factory mounting brackets and hardware from the existing

radio and attach them to the new radio using the same screws. Do not

exceed M5 x 9 MM maximum screw size. Longer screws may damage

components inside the chassis.

4. Wire the new radio to the vehicle as outlined in the Universal Installation

instructions.

5. Slide radio chassis into dash opening and secure with factory radio

screws.

6. Reinstall dash panel

Kit Installation

If your vehicle requires the use of an installation kit to mount this radio,

follow the instructions included with the installation kit to attach the radio to

the mounting plate supplied with the kit.

1. Wire and test the radio as outlined in the Universal Installation instruc-

tions.

2. Install the radio/mounting plate assembly to the sub-dashboard

according to the instructions in the installation kit.

3. Attach the support strap to the radio and dashboard as described in the

Universal Installation instructions.

4. Replace the dashboard trim panel.

Fuses

When replacing a fuse, make sure the new fuse is the correct type and

amperage. Using an incorrect fuse could damage the radio. The HD5112

uses one 15 amp fuse located below the wiring connector (15 amp fast blow

ATO).

Reconnecting the Battery

When wiring is complete, reconnect the battery negative terminal.

SCN

RPT

SHF

BAND

AUX-IN

CAT/DIR

SRC

FILE/FOLDER

A~Z

PRESS

0~9

MONO

MUTE

HD5112

SELECT

iPod

ENTER

TUNE/CH

DISP

SAT

ISO INSTALLATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jensen HD5112 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info