701362
6
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
INSTALLING THE MIDRANGE DRIVERS
IN FACTORY LOCATIONS:
Follow the same wiring procedures outlined for
the woofer installation.
The XR400-CM midrange drivers have been
designed to install, without modifications, into most
vehicles that accept a 4-inch (100 mm) speaker.
Most factory 4-inch speakers use four mounting
screws which will line up with the mounting holes
on your woofers. In most factory locations, it will
be necessary to use the supplied Flush Mount
Adaptor Rings as shown in the diagram.
Install as shown in the diagram below. Use the
supplied mounting clips unless the factory holes
already feature threaded inserts. Hand-tighten the
screws evenly to avoid bending the speaker frame!
Some vehicles which accept a 4-inch (100 mm)
speaker use a two-hole mounting system. This can
be easily accommodated by breaking off two of the
tabs as shown in the diagram at the top of this
page. All four mounting tabs are perforated to
permit their removal. Bend each unneeded tab
back and forth until it breaks off. Please be careful
in handling the speaker after breaking off the tabs as
there may be sharp edges.
6 JL AUDIO XR653-CS
INSTALLING THE MIDRANGE DRIVERS
IN CUSTOM LOCATIONS:
For custom-mounted applications, break off all
four mounting tabs and use the supplied Frame
Adaptors as shown in the diagrams on page 8.
These Frame Adaptors permit for a smaller overall
diameter when custom mounting the speakers and
must be used in order to install the supplied grilles.
Run the supplied speaker wires to the desired
mounting location. If you are running wires into a
door, use existing factory wiring boots whenever
possible. If you are drilling new holes, file their
edges and install rubber grommets into each hole.
Then, cover the wires with a protective PVC sleeve
and run them through the door jamb. Make sure
that the wires will clear door hinges and other
structures in the door. If you are unsure about any
part of this process, please contact your JL AUDIO
dealer for installation help.
Double check the clearance for both speakers
before proceeding.
Use the template supplied in the product
packaging to mark the desired mounting location.
Mark the center and the outline of the mounting
hole as well as the mounting screw positions. Before
drilling or cutting, use a utility knife to cut any fabric,
vinyl or leather from hole locations. These materials
can easily be snagged by a drill or a saw, causing
damage to the panel and possible bodily injury.
Four-Hole Mount Custom MountTwo-Hole Mount
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JL Audio XR653-CS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info