JE 50 RA 916 radio motor is a product from Jolly Motor España, s.l.www.enjoy-motors.com 4
JE50RA-916-STEEL_eng_ver. REM 2 & REM 2T
9-1REPLACEMENT THE FIRST EMITTER (Main emitter) through the Switch Power Off/On
switch
OFF/ON
BIP
2
’’
seconds
2
’
minutes
4
enjoy
Switch power OFF, in the motor which we
want replace the MAIN transmitetr.
After 5 seconds, switch power ON
Between 2 seconds and 2 minutes (and
six seconds) after the power ON, the motor
willmakeasingletiltmovementasconr-
mation that it is ready to learn a new Main
On the new Main Emitter:
Press FOUR times the P3 button (located
on the back of the emitter)
Then the motor will make two tilt movement
asconrmationthatthenewMainemitter
has been learned
During the replacement process:
•Any order send by a transmitter will stopped the replacement process (even if the order is coming from a transmitter not learned with the motor. It is enought with the same
frequency).
When we replace the MAIN transmitter:
•Old main transmitters doesn’t work with the motor.
•Old transmitters copied on the motor, remain working on the motor
•The limit switches set up remain memorized on the motor.
9-2REPLACEMENT THE FIRST EMITTER (Main emitter) through the Switch Power Off/On, if in the motor has not been seted up the limit switches
switch
OFF/ON
BIP
BIP
BIP
BIP
BIP
BIP
BIP
1
switch
OFF/ON
BIP
2
’’
seconds
2
’
minutes
4
Switch power OFF, in
the motor which we
want replace the MAIN
transmitter.
After 5 seconds, switch
power ON Motor will emit
till SEVEN BIPs
On the new Main Emitter:
Press ONE time the P3
button (located on the
back of the emitter)
Switch power OFF, in
the motor which we
want replace the MAIN
transmitter.
After 5 seconds, switch
power ON
Between 2 seconds and 2
minutes (and six seconds) after
the power ON, the motor will
make a single tilt movement as
conrmationthatitisreadyto
learn a new Main
On the new Main Emitter:
Press FOUR times the P3
button (located on the back
of the emitter)
Then the motor will make
two tilt movement as
conrmationthatthenew
Main emitter has been
learned
10FULL RESET (DELETE ALL TRANSMITTTERS, LIMIT SWITCHES SET UP, ...) through any transmitter learned on the motor
switch
OFF/ON
hold
5
’
seconds
BIP
BIP
BIP
BIP
12345678
BIPBIPBIPBIPBIPBIPBIPBIP
10
BIP
9
BIP
Switch power OFF, in the
motor which we want do
the FULL RESET. After 5
seconds, switch power ON
Press TEN times the P3 button (located on the back of the emitter). Be sure to HOLD pressing on the TEN time.
1. Transmitter (learned on the motors) doesn’t work:
•The battery is consumed, replaced it by a new one.
•Be sure that motor is powered ON.
•Check if any interference in disturbing the signal.
2. Motor is working Step by Step (deadman):
•No limit switches are setted up on the motor. Set up them (up and down). After that motor will work in automatic mode.
3. Up and Down buttons are not in correspondende with the motor movement:
•If you have not set up the limit switch, do it, starting with the down limit switch.
•If limit switches have been setted up, you have to delete it (point 5) and set up agin (point 4-1 and 4-2).
4. Atter a power OFF/ON, the motor is emitting till SEVEN BIPs:
•Limit switches have been not setted up, please set up them (points 4-1 and 4-2).
5. Main transmitter doesn’t work or it is missing:
•Replace the Main transmitter, follwong the instructions (point 9-1 or 9-2).
6. Roller shutter is stopping in a wrong point:
•Do a full movement in ecah direction (up and down). After that check again. If motor still not stopping on the desires point, will be necessary delete its limit switch (point 5)
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Jolly Motor JE50 RA9 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.