Bedienungsanleitung Jotul F 374 (Seite 19 von 104) (Englisch, Holländisch, Französisch, Italienisch, Spanisch)

467801

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

6.4 Inspection of the fireplace

Jøtul recommends that you personally inspect your fireplace

carefully after sweeping/cleaning. Check all visible surfaces for

cracks. Also check that all joints are sealed and that the gaskets

are in the correct position. Any gaskets showing signs of wear or

deformation must be replaced.

Thoroughly clean the gasket grooves, apply ceramic glue

(available from your local Jøtul dealer), and press the gasket well

into place. The joint will dry quickly.

6.5 Exterior maintenance

Painted products may change colour after several years usage. The

surface should be cleaned and brushed free of any loose particles

before new paint is applied.

7.0 Service

Warning! Any unauthorised change to the product is illegal.

Only use original spare parts.

7.1 Replacing the baffle/exhaust

deflector

(N.B. If you use tools, be aware that the vermiculite plates may

be damaged by rough treatment).

1. Lift up the front edge of the baffle plate and tilt it out

(fig. 29 G). Remove the side burn plates (fig. 29 F) and the

rear burn plate (fig. 29 E).

2. The exhaust deflector, in cast-iron - that is located above the

baffle plate, rests with the bar on the ribs at the rear flue

outlet (fig. 26 A). Lift the exhaust deflector slightly up, pull it

forward and tilt it out.

3. For reassembly follow the same procedure for installation,

but in reverse.

7.2 Replacement of burn plates/base

plate

(N.B. If you use tools, be aware that the vermiculite plates may

be damaged by rough treatment).

1. Lift up the front edge of the baffle plate and tilt it out. Remove

the side burn plates (fig. 29 F) and the rear burn plate (fig. 29 E).

2. Then lift up the grate and the base plate and take it out (fig.

29 D).

3. Follow the same procedure for installation, but in the opposite

sequence.

4. When reassembling the grate and the base plate, make sure

that the riddling bar (fig. 27 A) that moves the riddling grate

is threaded into the slot on the right edge of the grate.

7.3 Replacing the inner/outer side

glass

1. Lift up the front edge of the baffle plate and tilt it out Remove

the side burn plates (fig. 29 F) and the rear burn plate (fig. 29 E).

2. The exhaust deflector, in cast-iron - that is located above the

baffle plate, rests with the bar on the ribs at the rear flue

outlet (fig. 26 A). Lift the exhaust deflector slightly up, pull it

forward and tilt it out.

3. Remove riddling grate, base plate and ash pan (fig. 29 D).

Fig. 31

Fig. 32

4. Unscrew the upper and lower screws (fig. 31 A and 32 A), and

tilt the glass holder with the glass carefully out through the

door. N.B. The glass holder also keeps the outer glass in place

5. Remove the glass and possibly replace gaskets. If needed

replace the external glass.

6. For reassembly follow the same procedure for installation,

but in reverse.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jotul F 374 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info