Bedienungsanleitung Jotul F 520 (Seite 13 von 52) (Deutsch, Englisch, Holländisch)

657944

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ENGLISH

For fastening Ø 80 / Ø100 fresh air intake tube (optional

equipment – item no. 51047509 / 51012164), see the manual

(item no. 10047508) accompanying the external air set. See

the installation instructions that follow with the external air set.

Attach the hose to the external air connector with a hose clip

to avoid using joints. The external air hose insulation ends

approx. 100 mm below the burn chamber.

Fig. 8

Then install the cover for outdoor air inlet underneath of the

oven.

Through the oor

Fig. 9

100

• Use a heavy mallet and strike hard in the middle of the

knockout

• Pull a exible hose through the oor and up to the air

intake connector.

• Then attach the exible hose to the air intake connector

with a hose clamp

• For fastening Ø80 / Ø100 fresh air intake tube (optional

equipment – item no. 51047509 / 51012164), see the

manual (item no. 10047508) accompanying the external

air set. See the installation instructions that follow with

the external air set. Attach the hose to the external air

connector with a hose clip to avoid using joints. The

external air hose insulation ends approx. 100 mm below

the burn chamber.

4.4 Chimney and ue pipe

• The replace must only be connected to a chimney and

ue pipe approved for solid fuel replaces with ue gas

temperatures as specied in «2.0 Technical Data».

• Several solid fuel stoves can be connected to the same

chimney system if the chimney cross section is adequate.

NB: Look into the applicable rules and regulations to

nd out what is permitted. Even a good chimney can

function poorly if it is used incorrectly.

• The cross-section of the chimney must be designed to t the

replace. Use «2.0 Technical Data» to calculate the correct

chimney cross-section.

• The chimney must be connected in accordance with the

installation instructions of the chimney supplier.

• Before a hole is made in the chimney, the product should

be test-mounted in order to correctly mark the position of

the replace and the hole in the chimney. See g. 1 for

minimum dimensions.

• Make sure that the ue pipe rises all the way up to the

chimney.

• With a rear outlet, use a ue pipe bend with a sweep hatch

to allow sweeping.

• Please note that it is extremely important for connections to

have a degree of exibility. This is to prevent any movement

in the installation leading to the formation of cracks.

• For recommended chimney draught, see «2.0 Technical

Data». For ue pipe dimension see “2.0 Technical Data”.

NB: The chimney’s diameter must be at least just as big

as the ue pipe.

NB! The minimum recommended chimney length is 3.5 m

from the ue pipe insert. If the draught is too strong, a ue

pipe damper can be installed and used to reduce the draught.

Operation under different weather

conditions

The effect of the wind on the chimney may have a signicant

impact on how the stove reacts under different gust loads. It

may be necessary to adjust the air supply to achieve good

combustion.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jotul F 520 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info