Bedienungsanleitung Jotul F 520 (Seite 16 von 52) (Deutsch, Englisch, Holländisch)

657944

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

5.2 Stacking wood

Min 100 mm

• The wood must not be stacked higher than 100 mm from

the bottom of the stove.

6.0 Maintenance

6.1 Cleaning the glass

The product is equipped with an air wash for the glass. Air is

sucked in through the air vent on the top of the product and

down along the inside of the glass.

However, some soot will always stick to the glass, but the

quantity will depend on the local draught conditions and

adjustment of the air vent. Most of the soot layer will normally

be burned off when the air vent is opened all the way and a re

is burning briskly in the replace.

Good advice! For normal cleaning, moisten a paper towel

with warm water and add some ash from the burn chamber.

Rub it over the glass and then clean the glass with clean water.

Dry well. If it is necessary to clean the glass more thoroughly

we recommend using a glass cleaner (follow the instructions

on the bottle).

6.2 Cleaning and soot removal

Soot deposits may build up on the internal surfaces of the

replace during use. Soot is a good insulator and will therefore

reduce the replace’s heat output. If soot deposits accumulate

when using the product, they can easily be removed by using

a soot remover.

In order to prevent a water and tar layer from forming in the

replace, you should regularly allow the re to burn hot in order

to remove the layer. An annual internal cleaning is necessary

to get the best heating effect from your product. It is a good

idea to do this when cleaning the chimney and ue pipes.

6.3 Sweeping ue pipes to the

chimney

Flue pipes must be swept through the ue pipe sweeping

hatch or through the door opening. The bafe and exhaust

deector must be removed rst.

6.4 Inspection of the replace

Jøtul recommends that you carefully inspect your replace

yourself after it has been swept/cleaned. Check all visible

surfaces for cracks. Also check that all joints are sealed

and that the gaskets are in the correct position. Any gaskets

showing signs of wear or deformation must be replaced.

Thoroughly clean the gasket grooves, apply ceramic glue

(available from your local Jøtul dealer) and press the gasket

well into place. The joint will dry quickly.

6.5 Exterior maintenance

Painted products may change colour after several years’

usage. The surface should be cleaned and brushed free of

any loose particles before new paint is applied.

Enamelled products must only be cleaned with a clean, dry

cloth. Do not use water and soap. Any stains can be removed

with a cleaning uid (oven cleaner etc.).

7.0 Servicing

Warning! Any unauthorised changes to the product are

illegal! Only original spare parts may be used!

7.1 Service/replacing parts in the burn

chamber

NB: Use tools with great care! The vermiculite plates may be

damaged if treated roughly.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jotul F 520 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info