Bedienungsanleitung Jotul GF 400 (Seite 10 von 20) (Englisch)

467831

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Gas Installation

Gas installation must only be performed by qualified

personnel. It is important to adhere to national and local

regulations that apply. In the UK these include BS5440 Pt

1&2 and BS5871 in Ireland.

The LPG gas container must be stored/installed ac-

cording to national regulations. The gas container must

have a pressure regulator that reduces the pressure to the

required level. See technical data on page 4 for gas type

and pressures before connecting to the appliance. The

appliance must not be exposed to pressure above 55 mbar

(5,5 kPa) during pressure testing.

Gas tubes must be made of steel (DIN 2448/1629, DIN

2458/1626, DIN 2440, DIN 2441) or copper (DIN 2110).

For practical reasons, the vent system should be

installed before the appliance is connected to the gas

supply.

The stove is supplied with a 3/8” to 8 mm compres-

sion union. The gas valve has a 3/8” NPT threaded connec-

tion. All tube connections must be approved and the gas

pipeline must have an approved shutoff valve. Only use

approved sealing agent (tape) at all the pipe connections.

When the pipe sections have been assembled and con-

nected to the appliance, open the gas supply and light the

appliance (see lighting instructions). Perform a tightness

test on all the pipe connections.

Commissioning

Testing the Flue System

Once the appliance is fitted, gas leak and pressure tested,

and the flue system complete, the flue must be checked

for correct operation. This is best achieved after 10 min-

utes of burning by holding a smoke match just inside the

down-draught diverter hood on the rear of the appli-

ance, accessible through a cutout in the rear heat shield.

The smoke should be drawn into the flue and no smoke

should spill into the room. If the smoke does issue into the

room, leave for another 5 minutes and retest.

The appliance is fitted with a TTB (flue sensing safety

switch). If the fire does cut out automatically during flue

testing, or if smoke persists to come into the room when

tested, a problem is indicated within the flue system

which must be thoroughly measured, checked and recti-

fied before allowing use of the appliance.

Figure 18.

Proper pilot flame

/ carry-over port

alignment.

Figure 17. Valve pressure tap locations.

D E

Testing Gas Pressure

Correct gas pressure is important for the safe use of gas in

the appliance. It is important that the correct gas pressure

is set during the installation of the appliance.

The gas valve is equipped with outlets for the testing

of gas pressure. The outlets are located at the front of

the valve below the ON/OFF/Pilot knob. The outlets are

marked as shown in fig.17.

Outlet D: For gas pressure to the valve (volume of gas to

the valve) See technical data.

Outlet E: For gas pressure from the valve (volume of gas

coming out of the valve to the burner).

C: Regulator - Always test the gas pressure with the valve

regulator knob on High (Hi).

Loosen the screw in the outlet and attach the tube

from the manometer to the outlet. Remember to

tighten the screw when the testing is completed and

test for leaks at the outlets with test fluid.

Required gas pressure from the vent (Outlet E) is displayed

in the table below.

GAS TYPE MAX. / High Setting

Natural gas 9.20 mbar

Propane 25.6 mbar

Regulating the Pilot Flame

The pilot flame should have three flames as shown in fig.

18. The two thermo-element sticks should be surrounded

by two of the flames as shown in figs. 19. The flames

should be stable and the colour mainly blue. If you detect

a deviation from this,

turn off the pilot

flame and call for

service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jotul GF 400 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info