Bedienungsanleitung JRpropo XG14 (Seite 80 von 112) (Englisch)

606954

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

▋Bind▋and▋Range▋Check【BIND&RANGE】

▋▋Function▋Explanation

This function allows binding (pairing) with the receiver. In addition, transmitter power output

can be reduced for carrying out a range check.

▋▋Setting▋Method

⿟ Binding (BIND)

Set the receiver to the Bind Standby condition. Then rotate the dial to select “BIND” (inverse display) and press

the dial. If the display shows “SUCCESS”, binding has been successfully completed. If the display shows “TIMEOUT

PLEASE TRY AGAIN”, the bind process failed, and you must try again.

⿟ POWER (RF POWER) Range Check

If POWER is changed from “NORMAL” to “LOW”, the transmitter RF power is reduced and the LED will ash,

allowing a range check to be carried out. Place the Aircraft 40 meters (approx 131 feet) away from the

transmitter, and ensure all the controls function normally.

⿟ Regional Settings Mode (DMSS 2.4GHz Band width for France)

When using the transmitter in France and its overseas territories, this should be set to “FRANCE”. In all other

regions this should be set to “GENERAL”. In France mode, the 2.4GHz bandwidth that is used will be legally

restricted compared to the bandwidth in other regions. Initially it is set to “GENERAL”.

ダイヤル

TIPS

調整ポイント表示

ポイント接続を曲線に変更スティック入力位置と出力位置の数値表示

現在の

フライトモード位置

各調整ポイントの

入力位置と出力位置

ポイントの

追加と削除

注意：

グラフはホバリン

グスロットルやス

ロットルトリムで

変化する場合もあ

ります。

カーブをコピー

⿟ If there is a di󰮐culty in binding a receiver, please conrm the following:

፧

Are the transmitter and receiver batteries fully charged? Please fully charge the batteries.

፧

Are the transmitter and receiver too close to each other? If they are set too close each other, RF swamping

may interrupt the binding process. Please try binding again with the transmitter and receiver further

separated.

፧

If the transmitter and receiver are on a metal table or desk, binding may be di󰮐cult. Please try binding on

a di󰮏erent surface.

⿟ Each receiver recognizes the transmitter’s model ID. If the Model ID does not match the with particular model,

it may not be able to complete binding. This is to avoid matching the wrong model’s ID to the transmitter.

RefertothePage76"TransmitterSetting【TXSETTING】"

⿟ Only matching DMSS receivers may be bound to the transmitter.

▋▋Caution▋Note

⿟ Be sure to set the “FAIL SAFE” (under System List) after the binding procedure is complete. It is essential to use

the Fail safe to minimize the risks of RF signal loss. Be conscious about safety all the time. Check the actual

Fail safe settings by turning o󰮏 the transmitter, and monitoring the response of the servos.

⿟ When the model or type is changed in the transmitter, it will be necessary to re-bind the receiver.

⿟ NEVER y the aircraft in Range Check mode.

Helicopter

Airplane

DANGER

WARNING

CAUTION

Glider

System▋List

Bind Mode

XG14English.indd 78 2013/07/16 16:40

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JRpropo XG14 Seite 80

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info