Bedienungsanleitung JVC GR-DVL9200 (Seite 46 von 68) (Englisch)

584571

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

46 EN

–

ODE

SELECT SCENES

Point the remote control at the camcorder’s remote

sensor. Press PLAY (

) and then press R.A.EDIT ON/

OFF on the remote control.

The Random Assemble Editing Menu appears.

If using a Fade/Wipe at the beginning of the scene,

press FADE/WIPE on the remote control.

•Cycle through the effects by pressing repeatedly,

and stop when the one you want is displayed.

•You cannot use a Picture Wipe/Dissolve at the

beginning of Program 1.

At the beginning of the scene, press EDIT IN/OUT on

the remote control. The Edit-In position appears in

the Random Assemble Editing Menu.

At the end of the scene, press EDIT IN/OUT. The

Edit-Out position appears in the Random Assemble

Editing Menu.

If using a Fade/Wipe at the end of the scene, press

FADE/WIPE.

•Cycle through the effects by pressing repeatedly,

and stop when the one you want is displayed.

•If you select a Fade/Wipe effect for an Edit-Out

point, the effect is automatically applied to the

following Edit-In point.

•You cannot use a Picture Wipe/Dissolve at the end

of the last scene.

•When you use Fade/Wipe effects, that time is

included in the total time (this does not apply to

Picture Wipe/Dissolve).

If using Playback Special Effects, press EFFECT

(Z pg. 43).

Repeat steps 6 through 9 to register additional scenes.

•To change previously registered points, press

CANCEL on the remote control. The registered

points disappear, one at a time, from the most

recently registered point.

•If you are not using Fade/Wipe or Program AE with

special effects, repeat steps 6 and 7 only.

USING THE REMOTE CONTROL UNIT

(cont.)

NOTES:

●

When choosing a scene, set Edit-In and Edit-Out points so that there is a relatively large difference between

them.

●

If the search time for an in-point exceeds 5 minutes, the recording deck’s Record-Standby mode will be

cancelled and editing will not take place.

●

If there are blank portions before or after the Edit-In and Edit-Out points, a blue screen may be included in

the edited version.

●

Since time codes register time only as accurately as seconds, the time code total time may not match the

total programme time exactly.

●

Turning off the camcorder’s power erases all registered Edit-In and Edit-Out points.

●

If you select Sepia or Monotone mode from Program AE with special effects, you cannot use the Dissolve or

Black & White Fader. In this case the Dissolve or Black & White indicator begins blinking. Once the next

Edit-In point is registered, the effect is turned off. To combine these effects, use Sepia or Monotone during

recording, then use the Dissolve or Black & White Fader during Random Assemble Editing.

●

It is not possible to use Fade/Wipe effects and Programme AE with special effects during Random Assemble

Editing using a DV cable.

PLAY

R.A.EDIT

ON/OFF

EFFECT

Random Assemble

Editing Menu

Program

Remote sensor

CANCEL

RM-V716U

(provided)

EDIT IN/OUT

FADE/WIPE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC GR-DVL9200 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info