474088
10
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
three-step quick start10
FINISH AUTO SETUP
Press and move on to Step 2 to check the results.
oops! If there is a power cut or you accidentally press a button during Auto
Setup
, turn the VCR off and then on again. Re-perform Auto Setup.
before you start
Check that the VCR is
turned off and no
cassette is inserted
Load the battery into the
Remote Control
Refer to the Remote
Control diagram
on pages 6–7
Unless indicated
otherwise, use the
buttons on the Remote
Control
Check that the
connection is completed
Turn on the TV
S-VHS
VCR
S-VHS
VCR
Three-Step Quick Start
Auto Setup
START AUTO SETUP
Press the o button. If ‘Auto’ appears on the display panel, press OK (or E).
what will happen? The display panel on the front of the VCR will show the
word ‘Auto’. Do not press any button on the VCR or the Remote Control.
The VCR is automatically setting up the tuner
channels, clock, the VIDEO Plus+ system assigned
Guide Program numbers and the video channel.
This only happens the first time that the VCR is
turned on.
rf and scart connection If you have chosen to
connect the VCR to the TV with both the RF Cable
and a 21-pin SCART Cable (not provided) and the
TV set is in its AV mode (see the TV manual), you
will see the following information displayed on
your TV screen:
SELECT THE VIDEO CHANNEL
When
Auto Setup has finished, you will see the following display panel on your VCR:
rf cable only If you have only used the RF
Cable to connect the VCR to the TV, you will
see this display. The number is the channel on
the TV that the
Auto Setup has chosen to be the
video channel. In the example, we have
presumed that channel 52 is vacant and have set the VCR to 52:
Now tune the TV set to channel 52 (refer to TV manual if
necessary); you should see two vertical white bars appear
on the TV screen. If the bars do not appear or are not
clear, choose another vacant channel pressing PR +/ -- on
the Remote Control and try again. If you cannot obtain
the vertical white bars on any channel between 22 and 69,
consult your local JVC dealer.
rf and scart connection If you have chosen
to connect the VCR to the TV with both the RF
Cable and a 21-pin SCART Cable (not provided),
you need to press the PR -- on the Remote
Control until the figure reads ‘– –’. This is because you will use the TV in AV mode
to view video pictures and therefore do not need a dedicated video channel.
:
AUDIO
0000
VPS/PDC
3
5
3
2 4
30 SEC
?
PR
PR
PR
ENTER
LP00000-000
VCR/TV
i
ENTER
i
:
3
PR
PR
Auto Setup is running: don’t
touch any buttons
Your TV screen during Auto Setup if SCART is used
S-VHS
VCR
AUTO SET
PLEASE WAIT
[MENU]: EXIT
HR-S5965/5966EK-EN/p08-12 2/19/03, 04:08 PM10
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JVC HR-S5965 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info