Bedienungsanleitung JVC HR-S5965 (Seite 11 von 60) (Englisch)

474088

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

three step quick start 11

Check the Results

When Auto Setup finishes, you will see one of the three following examples on

the VCR display panel:

The Preset Positions and the Clock have been set successfully

Go straight to Step 3 (20:00 used as example only).

The Preset Positions have been set successfully but the Clock has not

Perform Clock Set on page 51.

Go to

Step 3.

Neither the Preset Positions or the Clock have been set successfully

Make sure the cables are connected properly to the VCR and turn

the VCR off and then on again. Try

Auto Set Up again.

Finish Off

Select the Video channel or AV mode, then make sure that all necessary stations

have been stored in the VCR’s memory by using the

and

buttons.

If station names (ID — ੬ pg.49) have also been stored in the VCR’s memory, the

station name will be displayed at the top left corner of the TV screen for about 5

seconds each time you select a different channel via the VCR.

The VCR is now set up. You can now use it to play and record.

IMPORTANT

•

re-running setup Auto Setup may not behave as described if it has already

been run on the VCR. This is because some of the information gathered on the

first Auto Setup- is retained in memory and that part of the process may be

skipped by the VCR.

•

bad reception In certain reception conditions, station names may not be

stored correctly, and

Guide Program Numbers may not be set properly. If this

happens, when you timer-record a TV programme using the VIDEO Plus+

system, the VCR will record a TV programme of a different station. When

programming the timer using the VIDEO Plus+ system, be sure to check that

the preset position corresponding to the broadcasting station you wish to

record has been selected (੬ pg.21,

VIDEO Plus+ Timer Programming).

•

duplicate stations You may be able to receive the same station from two

different transmitters in which case Auto Setup will detect and store both. It is

normal for one transmitter to give you a better quality picture than the other; to

delete those stations which have a poor picture ੬

Delete A Channel on page47.

•

manual station setting If any of the above problems occur, refer to

pages47–48 to input station names (੬

Change Station Name). You can also

change station preset positions (੬

Change Station Preset Position).

•

rf connections In certain reception conditions, the Video Channel may not

be set correctly and interference may appear in the TV picture while the VCR’s

power is on. Set your Video Channel manually. (੬ pg.44,

Video Channel Set)

IF YOU HAVE ANY DIFFICULTY WITH THE ABOVE PROCEDURES CALL THE JVC

CUSTOMER SERVICE HOT LINE ON 0870 330 5000

– –:– –

AUDIO

0000

VPS/PDC

2 4

30 SEC

ENTER

LP00000-000

VCR/TV

HR-S5965/5966EK-EN/p08-12 2/19/03, 04:08 PM11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC HR-S5965 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info