Bedienungsanleitung JVC HR-S9911U (Seite 21 von 32) (Englisch)

658632

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

—21—

䡵 AV COMPU-LINK — ON/OFF

The REMOTE PAUSE/AV COMPULINK terminal on the rear panel

can be used as either the REMOTE PAUSE terminal or the AV

COMPULINK terminal.

● When this function is set to “ON”, you can use this terminal as

the AV COMPULINK terminal. By connecting other JVC’s AV

COMPULINK components, including amplifiers (or receivers)

and televisions, one touch control of the audio and video

components linked via their AV COMPULINK connectors

becomes possible.

● When this function is set to “OFF”, you can use this terminal as

the REMOTE PAUSE terminal. If your JVC camcorder is

equipped with the Master Edit Control, you can control the VCR

from the camcorder. Connect the mini-plug cable (not supplied

with this VCR) between the REMOTE PAUSE terminal and the

EDIT connector on the camcorder.

NOTE:

Refer to the other components’ instruction manuals for connection

and its operations.

䡵 FRONT AUX INPUT — VIDEO/S-VIDEO

You have to select which terminal — either VIDEO (composite) or

S VIDEO (Y/C separate signals) to use as the video input terminal

on the front panel.

Make sure to select the correct terminal; otherwise, you may fail

in recording (editing) on this VCR.

䡵 REAR AUX INPUT — VIDEO/S-VIDEO

You have to select which terminal — either VIDEO (composite) or

S VIDEO (Y/C separate signals) to use as the video input terminal

on the rear panel.

Make sure you select the correct terminal; otherwise, you may fail

in recording (editing) on this VCR.

Satellite Auto Recording

You can automatically record a satellite program which is timer-

programed on your DBS receiver.

A Connect a DBS receiver to the AUDIO/VIDEO IN or S VIDEO IN

connectors* on the rear panel. You can also connect the cable

box if it has a timer.

* To use these connectors, you have to select which one to use.

(

墌 See above, “REAR AUX INPUT”.)

B Set timer program on DBS receiver using its instruction

manual.

C Load a cassette with the record safety tab intact.

D Press SP/EP (p) to set the tape speed. The selected tape

speed will appear on the TV screen.

E Press REC LINK for more than 2 seconds. The VCR turns off

automatically and enters the Satellite Auto Recording standby

mode and the REC LINK lamp lights. When the DBS receiver

outputs a signal, the VCR starts recording and the REC LINK

lamp blinks. The VCR stops recording and powers off when the

DBS receiver stops outputting a signal.

NOTES:

● Be sure not to turn on the DBS receiver before the program starts

broadcasting; otherwise, the VCR will start recording when the

DBS receiver is turned on.

● To disengage the Satellite Auto Recording standby mode, press

REC LINK (the REC LINK lamp goes off).

● Depending on the type of DBS receiver, Satellite Auto Recording

may not be compatible.

Child Lock

You can disable the VCR operations. While

the VCR is turned on, press and hold

POWER on the Remote

for more than

10 seconds. The VCR turns off, “CL”

appears for about 5 seconds on the display

panel.

To release the child lock, press and hold POWER on the Remote

until the VCR turns on.

NOTES:

● Pressing TIMER (#) during timer recording, unplugging the AC

power cord or a power outage also releases the child lock.

● Even if the child lock function is in use, it is possible to engage

and disengage the timer mode with TIMER (#) on the Remote.

Keep the Remote out of the children’s reach.

● Timer recording programs will be performed even if the child

lock function is activated.

JLIP ID Number Setting

The JLIP (Joint Level Interface Protocol) terminal is used to connect

the VCR to a personal computer or similar device. By connecting

through the JLIP terminals, you can control the VCR during editing

and certain other operations, from the connected personal

computer or similar device.

When connecting this VCR to another device using the JLIP

terminals, each device must have a different JLIP ID number.

The JLIP ID number of this VCR is preset to “1” when shipped

from the factory. You can change this number to any other number

between 1 to 99.

NOTE:

For further details on the JLIP system or devices, consult your

nearest JVC dealer.

A Access Main Menu screen, then Initial Set screen

Press MENU on the Remote. Press rt to move the highlight bar

(arrow) to “INITIAL SET”, then press OK or

B Access JLIP ID Number Set screen

Press rt to move the highlight bar

(arrow) to “JLIP ID NO. SET”, then press

OK or

C Set JLIP ID number

Press the appropriate Number keys on the

Remote to enter the desired ID number,

then press OK.

Press MENU to return to normal screen.

● Turn on the VCR and TV, and select the VCR channel (or AV

mode).

● Set the VCR/TV/CABLE/DBS selector on the Remote to

“VCR”.

● Turn on the VCR and TV, and select the VCR channel (or AV

mode).

● Set the VCR/TV/CABLE/DBS selector on the Remote to

“VCR”.

● Turn on the VCR and TV, and select the VCR channel (or AV

mode).

● Set the VCR/TV/CABLE/DBS selector on the Remote to

“VCR”.

Child lock

indicator

HR-S9911U-EN.fm Page 21 Friday, April 26, 2002 11:37 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC HR-S9911U Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info