Bedienungsanleitung JVC KD-X172DB (Seite 24 von 172) (Englisch, Holländisch, Portugiesisch, Spanisch)

732186

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

ENGLISH

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Pair and connect a Bluetooth device for the first time

Press B SRC to turn on the unit.

2 Search and select the name of your receiver (“KD-X472DBT”/

“KD-X272DBT”) on the Bluetooth device.

“BT PAIRING” flashes on the display.

• For some Bluetooth devices, you may need to enter the Personal

Identification Number (PIN) code immediately after searching.

3 Perform (A) or (B) depending on what appears on the display.

For some Bluetooth devices, pairing sequence may vary from the steps

described below.

(A) “Device Name” “XXXXXX” “VOL–YES” “BACK–NO”

“XXXXXX” is a 6-digit passkey randomly generated during each

pairing.

Ensure that the passkeys appear on the unit and Bluetooth

device are the same.

Press the volume knob to confirm the passkey.

Operate the Bluetooth device to confirm the passkey.

(B) “Device Name” “VOL–YES” “BACK–NO”

Press the volume knob to start pairing.

• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN

code “0000” into the Bluetooth device.

You can change to a desired PIN code before pairing.

(Page 19)

• If only “PAIRING” appears, operate the Bluetooth device to

confirm pairing.

“PAIRING COMPLETED” appears when pairing is completed and “” will light

up when the Bluetooth connection is established.

• KD-X472DBT: “

” indicator lights up to show the strength of the battery of

the connected device.

See also

[FORMAT]

on page 31 for the battery and signal strength shown

on the display.

• KD-X272DBT: “

” and/or “ ” indicator(s) light(s) up.

• This unit supports Secure Simple Pairing (SSP).

• Up to five devices can be registered (paired) in total.

• Once the pairing is completed, the Bluetooth device will remain registered

in the unit even if you reset the unit. To delete the paired device, see

[DEVICE DELETE]

on page 19.

• A maximum of two Bluetooth phones and one Bluetooth audio device can

be connected at any time. To connect or disconnect the registered device,

see

[PHONESELECT]

[AUDIOSELECT]

[BTMODE]

. (Page 19)

However, while in BT AUDIO source, you can connect to five Bluetooth

audio devices and switch between these five devices. (Page 21)

• Some Bluetooth devices may not automatically connect to the unit after

pairing. Connect the device to the unit manually.

• When the battery of the connected Bluetooth device runs low, “Device

Name”

“LOW BATTERY” appears.

• Refer to the instruction manual of the Bluetooth device for more

information.

Auto Pairing

(for KD-X472DBT)

When you connect iPhone/iPod touch to the USB input terminal, pairing

request (via Bluetooth) is automatically activated if

[AUTO PAIRING]

is set to

[ON]

. (Page 20)

Press the volume knob to pair once you have confirmed the device name.

Bluetooth®

(for KD-X472DBT/KD-X272DBT)

JS_JVC_KD_X472DBT_E_EN_4a.indd 16JS_JVC_KD_X472DBT_E_EN_4a.indd 16 10/24/2019 11:34:22 AM10/24/2019 11:34:22 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC KD-X172DB Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC KD-X172DB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info