57204
59
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
54
Convenient functions of TV viewing
IMPORTANT
Slide the remote control mode
selector to the lowest position.
1 Press [VCR].
2 Hold down [STB/VCR F].
• Hold down [STB/VCR F] until you finish
step 5.
3 Press [ENTER] and release.
4 Press number buttons to enter the
manufacturer code.
Examples:
For a Hitachi VCR: Press [0], then [8].
For a Toshiba VCR: Press [3], then [3].
When the manufacturer of your VCR has 2 or more
codes, select the manufacturer codes in turn and
find the one that operates the VCR and the remote
control properly.
The initial code setting is “01 (JVC)”.
5 Release [STB/VCR F].
NOTE
It is recommended that you slide the remote
control mode selector to [AUDIO] after using this
function. Most of the other functions can be used
when the remote control mode selector is at
[AUDIO].
Manufacturer codes are subject to change with-
out notice. You may not be able to operate the
VCR produced by the manufacturer.
After replacing the batteries of the remote con-
trol, set the manufacturer code again.
Before the VCR operation, select the remote con-
trol mode for the VCR.
IMPORTANT
Slide the remote control mode
selector to the lowest position.
1 Press [VCR].
2 Operate the remote control by
pointing it at the VCR.
NOTE
When the remote control mode selector is slid to
the lowest position and [VCR] is pressed, some
buttons may not work.
It is recommended that you slide the remote
control mode selector to [AUDIO] after using this
function. Most of the other functions can be used
when the remote control mode selector is at
[AUDIO].
Operating a VCR using the
remote control
Manufacturer
Code
Manufacturer
Code
JVC 01 Nokia 16
Aiwa 02, 20
Nordmende
17, 18, 19,
31
Bell+Howell
03, 16 Orion 20
Blaupunkt 04 Panasonic 21
CGM 03, 05, 16 Philips 05, 22
Daewoo 34 Phonola 05
DIGTAL 05 Saba
17, 18, 19,
23, 31
Fisher 03, 16 Samsung 24, 25
G.E. 06 Sanyo 03, 16
Grundig 07 Sharp 26, 27
Hitachi 08, 09 Siemens 07
Loewe 05, 10, 11 Sony
28, 29, 30,
35
Magnavox 04, 05
Telefunken
17, 18, 19,
31, 32
Mitsubishi
12, 13, 14,
15
Toshiba 33
Setting the manufacturer code
Remote control button Usage
[STB/VCR F] Turns on/off the VCR.
[CH +/
] Changes channels.
Number buttons
(1-10, 0, 10)
Selects the channels.
3 (playback) Starts playback.
7
Stops playback.
8 Pauses playback.
¡ Fast-forwards the tape.
1 Fast-rewinds the tape.
[REC] + 3 (playback) Starts recording.
[REC] + 8 Pauses recording.
Using the remote control for the
VCR operation
For the locations of the remote
control buttons, refer to page 51.
NX-F3_NX-F7[B].book Page 54 Tuesday, January 15, 2008 4:39 PM
59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JVC NX-F7 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von JVC NX-F7

JVC NX-F7 Bedienungsanleitung - Deutsch - 139 seiten

JVC NX-F7 Bedienungsanleitung - Holländisch - 139 seiten

JVC NX-F7 Bedienungsanleitung - Französisch - 139 seiten

JVC NX-F7 Bedienungsanleitung - Italienisch - 139 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info