469766
16
Zoom out
Zoom in
Vorherige Seite
1/50
Nächste Seite
13
Basic Settings
DVD STB VCR TV TAPE
FM/AM
TV DIRECT
DVD
MEMORY
CONTROL
ADJUST
SETTING
STANDBY
DIGITAL
DIGITAL
SURROUND
INPUT
ANALOG/DIGITAL
INPUT ATT
MASTER VOLUME
SURROUND
ON/OFF
DSP
MODE
ANALOG
PRO LOGIC
SUBWFR LFE
SLEEP RDS EON TA STTUNEDINFOHEWS MUTING
MH
Z
KH
Z
VOL
AUTO
DGTL AUTO
INPUT ATT
DSP
LCR
LS S RS
LPCM
DOLBY D
DTS
RX-E100R
DVD STB VCR TV TAPE FM/AM
HOME CINEMA CONTROL CENTER
STANDBY/ON
Setting the Digital Input
Terminals
When you use the digital input terminals, register what components
are connected to which terminals (DIGITAL IN 1/2) so that the
correct source name will appear when you select the digital source.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Press SETTING.
The CONTROL buttons now work for basic
settings.
2
Press CONTROL (or 5) repeatedly until
“DGT (Digital)” (with the current setting)
*
appears on the display.
* “1DVD2STB” is the initial setting. If you have already
changed setting, another combination will be shown.
3
Press CONTROL 3 (or 2) to select the
appropriate digital terminal setting.
Each time you press the button, the display changes to show
the following:
SETTING
Remote
NOT
CONTROL
VOL
CONTROL
5//3/2
Display
Basic Operations/Basic Settings
(back to the begining)
ANALOG
PRO LOGIC
SUBWFR LFE
VOL
DGTL AUTO
INPUT ATT
DSP
LCR
LS S RS
LPCM
DOLBY D
DTS
CONTROL
Note:
When shipped from the factory, the DIGITAL IN terminals have been
set for use with the following components.
DIGITAL 1 (coaxial): For DVD player
DIGITAL 2 (optical): For STB
Selecting the Analogue or Digital Input Mode
When you have connected digital source components using both the
analogue connection and the digital connection methods (see page
7), you need to select the input mode correctly.
1
Press one of the source selecting buttons (DVD,
STB, or TV)
* for which you want to change the
input mode.
Note:
*
Among the sources listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for. (See “Setting the Digital Input Terminals” .)
2
Press INPUT ANALOG/DIGITAL (or
ANALOG/DIGITAL INPUT on the remote
control) to select the analogue or digital input
mode.
Each time you press the button, the input mode alternates
between the analogue input (ANALOGUE) and the digital
input (DGTL AUTO).
DVD STB VCR TV
DVD
TO BE CONTINUED TO THE NEXT PAGE
Source selecting buttons
(DVD, STB, TV)
INPUT
ANALOG/DIGITAL
Source indicators
SETTING
SUBWFR LFE
DGTL AUTO
LCR
LS RS
DOLBY D
INPUT
ANALOG/DIGITAL
INPUT ATT
EN10-19.RX-E100RSL[B]_f 01.3.8, 2:50 PM13
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JVC RX-E100RSL wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von JVC RX-E100RSL

JVC RX-E100RSL Bedienungsanleitung - Holländisch - 50 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info