469766
17
Zoom out
Zoom in
Vorherige Seite
1/50
Nächste Seite
14
Basic Settings
DVD STB VCR TV TAPE
FM/AM
TV DIRECT
DVD
MEMORY
CONTROL
ADJUST
SETTING
STANDBY
DIGITAL
DIGITAL
SURROUND
INPUT
ANALOG/DIGITAL
INPUT ATT
MASTER VOLUME
SURROUND
ON/OFF
DSP
MODE
ANALOG
PRO LOGIC
SUBWFR LFE
SLEEP RDS EON TA STTUNEDINFOHEWS MUTING
MH
Z
KH
Z
VOL
AUTO
DGTL AUTO
INPUT ATT
DSP
LCR
LS S RS
LPCM
DOLBY D
DTS
RX-E100R
DVD STB VCR TV TAPE FM/AM
HOME CINEMA CONTROL CENTER
STANDBY/ON
Display Source indicators
INPUT
ANALOG/DIGITAL
Source selecting buttons
(DVD, STB, TV)
SETTING
CONTROL
5//3/2
If the following symptoms occur while playing Dolby Digital or
DTS Digital Surround software with “DGTL AUTO” selected,
follow the procedure below.
Sound does not come out at the beginning of playback.
Noise comes out while searching or skipping chapters or tracks.
1
Press one of the source selecting buttons (DVD, STB, or TV) for
which you want to change the input mode.
2
Press INPUT ANALOG/DIGITAL (or
ANALOG/DIGITAL INPUT) to select the digital input mode
(DGTL AUTO).
3
Press CONTROL 3 (or 2) to select “DGTL
D.D.” or “DGTL DTS” while “DGTL AUTO”
still remains on the display.
Each time you press the button, the digital input mode changes
as follows:
DGTL AUTO :Select this for the digital input mode. The unit
automatically detects the incoming signal
format. (The DGTL AUTO indicator lights up
on the display, then the digital signal indicator
for the detected signals lights up.)
ANALOGUE : Select this for the analogue input mode. (Initial
setting when shipped from the factory.)
To play back software encoded with Dolby Digital, select
“DGTL D.D.
To play back software encoded with DTS Digital Surround,
select “DGTL DTS.
Note:
When you turn off the power or select another source, “DGTL DTS”
and “DGTL D.D.” are canceled and the digital input mode is
automatically reset to “DGTL AUTO.
The following are the analogue/digital signal indicators on the
display to indicate what type of the signal comes into the unit.
ANALOGUE : Lights when the analogue input is selected.
LPCM : Lights when Linear PCM signals come in.
DOLBY D : • Lights when Dolby Digital signals come in.
Flashes when “DGTL D.D.” is selected for
software not encoded with Dolby Digital.
DTS : Lights when DTS Digital Surround signals
come in.
Flashes when “DGTL DTS” is selected for
software not encoded with DTS Digital
Surround.
Note:
When “DGTL AUTO” cannot recognize the incoming signals, no digital
signal indicators light up on the display.
DVD STB VCR TV
DVD
INPUT
ANALOG/DIGITAL
INPUT ATT
Remote
NOT
SUBWFR LFE
M
U
M
H
K
H
V
O
DGTL AUTO
LCR
LS RS
DOLBY D
When “DGTL D.D.” or “DGTL DTS” is
selected, “AUTO” goes off.
CONTROL
EN10-19.RX-E100RSL[B]_f 01.3.8, 2:50 PM14
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JVC RX-E100RSL wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von JVC RX-E100RSL

JVC RX-E100RSL Bedienungsanleitung - Holländisch - 50 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info