Bedienungsanleitung JVC TH-A10R (Seite 21 von 68) (Englisch)

57099

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

When a decode mode which differs from the type of

disc being played is selected

Insert a DVD disc in the center unit to display the type of audio

being played in the Decode mode indicator in the display window.

Audio cannot be played if a decode mode which differs from the

displayed mode is selected.

The selected decode mode flashes to indicate that the selected

decode mode does not allow audio playback.

Example: When DTS is selected as the decode mode for Dolby

digital audio.

Adjusting the Input Signal Level

When using the DSP mode effect during playback from an analog

device, the sound will occasionally be distorted due to a overly-

strong input signal. In these instances, it is possible to adjust the

level of the input signal. Only input signals from analog devices (TV

SOUND, VCR, TAPE, AUX, FM, AM, MD, DBS) may be adjusted

in this way.

On the front panel only:

1 Press and hold INPUT ATT. (DSP MODE).

Release the button when the display window shows “INPUT

ATT ON,” or “INPUT NORMAL.”

Pressing and holding the INPUT ATT. Button further cycles

through the following modes:

INPUT NORMAL: Playback source without adjusting the input

signal level. This is the default setting.

INPUT ATT ON: Lower the input level and playback source.

The ATT mark will light up.

To change the input signal level, press and hold INPUT ATT.

until “INPUT NORMAL” or “INPUT ATT ON” is displayed.

Note:

• When in “INPUT ATT ON” mode, ATT will light up in the

display window. However, when the playback source is digital

(DVD, etc.) it will go off. Lighting up will resume if playback is

switched to an analog device.

• Even while in “INPUT ATT ON” mode, if the DSP mode is

turned off (“DSP OFF”), playback will continue without any

reduction of the input signal.

Basic operations

VOLUME knob

PHASE button

Sub-woofer volume control and

phase setting

Use the VOLUME knob and PHASE button at the rear of the

powered sub-woofer.

Volume control ———————————————

Turn the VOLUME knob.

Adjust to a volume appropriate for balance with the other speaker(s).

The mark indicates the volume position in normal use.

• Adjust when the volume from the sub-woofer is too high or too

low in relation to the volume from the front speaker.

Phase setting ————————————————

Play sound through the sub-woofer and adjust the

PHASE button to a position (_ REVERSE or — NORMAL)

at which the lowest frequency is heard best.

Note:

• Phase is closely related to the distance from the listening position

to the front speaker and sub-woofer.

While listening, adjust until the lowest frequency is heard best.

Audio channel display lamp

Uses lamps to display the audio channel configuration for the disc

currently playing.

The lamps refer to the speaker channel as follows.

L: Left front speaker channnel

R: Right front speaker channel

C: Center speaker channel

RS: Right surround speaker channel

LS: Left surround speaker channel

S: Rear speaker channel (monaural)

LFE: Sub-woofer channel

Mark

Flashes

• The audio

channel display

lamp is not an

indicator of

which speakers

are producing

sound.

TH-A10[J]2/1 00.2.24, 14:4919

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC TH-A10R Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC TH-A10R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info