Bedienungsanleitung Kalkhoff 2021 (Seite 25 von 70) (Englisch)

778421

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

Originalbetriebsanleitung Allgemein EN-25

1. Open the tensioning lever by folding it by 180˚.

OPEN must now be visible.

2. Move the seat post into the right position.

3. Close the tensioning lever by swinging the lever by

180˚. CLOSE should now be visible. The lever should

be very easy to move from the beginning of the closing

movement up to halfway. Then, the force required to

move the lever must signicantly increase until the

lever is very dicult to move at the end.

4. a) If the quick-release skewer closes too easily, the

pre-tension must be increased: To do this, open the

tensioning lever and slide the seat post into the

desired position. Then, hold the tensioning lever and

turn the clamping nut on the opposite side clockwise.

Check whether the correct pre-tensioning has been

achieved by closing the tensioning lever.

b) If the quick-release skewer is too dicult to

close, the pre-tension must be reduced: To do this,

open the tensioning lever and slide the seat post

into the desired position. Then, hold the tensioning

lever and turn the clamping nut on the opposite

side counterclockwise. Check whether the correct

pre-tensioning has been achieved by closing the

tensioning lever.

5. Close the tensioning lever. The lever must be

positioned in such a way that it cannot be opened

accidentally.

6. Try to twist the saddle to check that it is rmly xed.

17.2 Lowerable seat post

Warning

Serious falls due to locked rear wheel.

▪ Before your rst ride, check whether the rear wheel

is locked by the lowering of the seat post. If the

saddle comes into contact with the rear wheel in its

lowest position, the insertion depth of the seat post

must be reduced. Make sure, however, that the seat

post is inserted at least 10 cm into the seat tube.

Information

If you want to retrot a lowerable seat post to your bi-

cycle at a later stage, it is possible that the tightening

torques for the seat post clamping screw(s) are lower

than the values given on the seat post clamp or in the

component operating instructions.

Adjustment screw

Screw

Fig. 20 Lowerable seat post Fig. 21 Control element

Lever

If your bicycle is tted with a lowerable seat post, you can

adjust the height of the seat post while riding. This is done

using the control element on the handlebars. Pressing the

lever either raises or lowers the seat post. Releasing the

lever locks the seat post in the corresponding position.

17.2.1 Positioning the control element

1. Loosen the screw on the control element by turning it

two to three turns anticlockwise.

2. Position the control element in the desired position.

3. Tighten the screw again by rotating it clockwise to

the specied torque using a torque wrench  13.

Tightening torques for threaded connections Page EN-19.

17.2.2 Changingtheleverpressure

If the lever is very dicult to press, it can make sense to

decrease the cable tension:

1. Turn the adjustment screw one or two turns

counterclockwise to decrease the tension.

If the lever is too easy to push and it is actuated too easily,

it can make sense to increase the tensile stress:

2. Turn the adjustment screw clockwise to increase the

tension.

17.3 Suspension seat post

Ask your cycle dealer to adjust the suspension elements

of the seat post.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kalkhoff 2021 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kalkhoff 2021

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info