Bedienungsanleitung Kalkhoff 2021 (Seite 27 von 70) (Englisch)

778421

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

Originalbetriebsanleitung Allgemein EN-27

3. Tighten the front and rear clamping screws clockwise

to the specied torque using a torque wrench  13.

Tightening torques for threaded connections Page EN-19.

Use approximately the same tightening torque for both

screws.

4. Tilting the saddle: Most riders prefer a horizontal

saddle. If you prefer the saddle to be slightly inclined,

however, loosen both clamping screws alternately by

turning these counterclockwise. Turn the clamping

screws completely two to three times at most,

otherwise the whole mechanism could fall apart. The

angle of the saddle will change as soon as you turn the

clamping screws.

5. Tighten both clamping screws equally clockwise so

that the saddle stays at the same angle.

6. Now, use a torque wrench to tighten the screws to the

specied torque  13. Tightening torques for threaded

connections Page EN-19.

7. Ensure that the newly-tightened saddle does not

tip; test it by pressing down on the front and back

alternately. After approximately 50 km, tighten the

saddle clamping screws again  13. Tightening torques

for threaded connections Page EN-19.

18.2 Dual-screw seat post I: adjusting the

seating position

STOP STOP

Seat post

Seat stay

Fig. 24a Setting the seating position

Clamping screws

STOP STOP

Clamping screws Seat post

Seat stay

Fig. 24b Setting the seating position

1. Movingthesaddle: Loosen the rear clamping screw by

turning it anticlockwise. Turn the rear clamping screw

completely two to three times at most, otherwise the

whole mechanism could fall apart.

2. Move the saddle horizontally. Stay within the marking

and ensure (e.g., using a spirit level) that the saddle

is horizontal.

18.3 Dual-screw seat post II: adjusting the

seating position

STOP STOP

Clamping screw Seat post

Adjustment screw

Fig. 25 Setting the seating position

1. Movingthesaddle:Loosen the clamping screw by

turning it anticlockwise. Turn the screw completely

two to three times at most or the whole mechanism

could fall apart.

2. Move the saddle horizontally. Stay within the marking

and ensure (e.g., using a spirit level) that the saddle

is horizontal.

3. Secure the clamping screw by tightening it clockwise

to the specied torque using a torque wrench  13.

Tightening torques for threaded connections Page EN-19.

Ensure that the clamping screw is straight and comple-

tely screwed into the nut.

4. Tilting the saddle: Most riders prefer a horizontal

saddle. If you prefer the saddle to be slightly inclined,

however, turn the adjustment screw clockwise slightly

to move the saddle nose downward. To move the

saddle nose upward, turn it counterclockwise slightly.

The adjustment screw must be screwed in to a depth of

at least 9 mm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kalkhoff 2021 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kalkhoff 2021

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info