Bedienungsanleitung Karcher Audio UR1309D (Seite 21 von 28) (Deutsch, Englisch)

733569

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

EN | 21

Volume Control

• Increase the volume by pressing the VOL ▲ button.

• Decrease the volume by pressing the VOL ▼ button.

Display Backlight & Timeout Function

The display backlight can be set in 4 levels (High / Medium / Low / O).

• To select between the settings press the DIMMER button repeatedly.

If you would like to have the display backlight switch o automatically after a certain time (Timeout

Function) rather than having the backlight on steadily, you can do so in the DAB+ or FM menu:

• While in radio mode (DAB+ or FM) press and hold for 2 seconds the MENU button to enter the

menu. Navigate to the submenu TIMEOUT (under System settings). Here you can select the time

after which the backlight will dim down again automatically (ON, 10 to 180 seconds).

• When you select “ON”, the display backlight will remain at the set level and not switch o.

Note:

• For a description on how to navigate through the menus, see the chapters “DAB+ Radio” and

“FM Radio”.

Sleep Timer

The sleep function enables you to set a countdown timer after which the unit will turn itself into standby

mode automatically.

• While in any mode, repeatedly press the SLEEP button until you’ve reached the desired sleep

timer duration (10 - 90 minutes in 10 minute intervals).

• The display will show the sleep indicator and the unit will switch to standby mode after the set

duration.

• To check how much time is left on the set timer, press the SLEEP button once.

• To cancel the sleep function, repeatedly press the SLEEP button until you’ve reached “00”.

Initial Setup

When you switch the unit on for the rst time, it will start up in DAB+ mode and automatically scan for

available radio stations. After the full scan is nished, the unit will play the rst found station.

Time is synchronized automatically with the DAB+ signal, so the clock does not need to be set manu-

ally.

Clock

Clock Synchronization

By default the clock is set to be synchronized automatically with radio signals (see “Initial Setup”).

If you would like to set the clock manually, you can do so as follows:

Manual Clock Setting

The clock can only be set while the unit is in standby mode.

1. While the unit is in standby mode, press the MENU button to enter the main menu. “Set Clock”

will be shown as rst menu item. Press the SELECT button to enter the clock setting.

2. Select between 12h display and 24h display by pressing the TUNE / buttons. Conrm your

setting by pressing the SELECT button.

3. The hours will start ashing. Set the current hours by pressing the TUNE / buttons. Press

the SELECT button again.

4. The minutes will start ashing. Set the current minutes by pressing the TUNE / buttons.

5. Press the SELECT button again to conrm all settings. The time is now set.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher Audio UR1309D Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info