Bedienungsanleitung Karcher B60 (Seite 20 von 300) (Alle Sprachen)

804747

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

- 7

1 Wear indicator

2 Vacuum lip

The vacuum lips must be replaced or re-

versed if they are worn down to the wear in-

dicator.

Remove the vacuum bar.

Unscrew the star grips.

Remove the plastic parts.

Remove the vacuum lips.

Insert new or reversed vacuum lips.

Insert the plastic parts.

Screw in and tighten the star grips.

Remove the rubber strip and clean the

channel with a cloth. After cleaning, re-

place the rubber strip evenly.

Lift the cleaning head.

Loosen the lock of the wiper flap.

Push the bearing lid down and remove.

Pull out the brush roller.

Note: The brush rollers must be re-

placed when the bristle length has

reached 10 mm.

Insert a new brush roller.

Reassemble the bearing lid in the re-

verse sequence.

Repeat process on the opposite side.

Lift the cleaning head.

Press the pedal for changing the brush-

es downward beyond its resistance.

Pull the disc brush out of the side below

the cleaning head.

Hold the new disc brush under the

cleaning head, push upward and lock.

Push the appliance forward about 2 m

so that the steering rollers point toward

the rear.

Press the pedal for lowering the clean-

ing head downwards slightly and then

move it to the left. This unlocks the ped-

al. Release the pedal slowly upwards.

The lift arm of the cleaning head will be

lowered.

1 Spring element

2 Locking pin

3 Terminal strip cover

4 Lock of safety pin

5 Excenter lever

Remove the terminal strip cover.

Place the cleaning head halfway in front

of the appliance.

Connect the mains supply cable of the

cleaning head to the appliance.

Attach the terminal strip cover.

Connect the hose couplers on the cleaning

head to the hose on the appliance.

1 Push handle

2 Cleaning head

Insert the push bow into the cleaning

head intake.

1 Safety splint

Insert the locking pins from below into

the mount of the cleaning head.

1 Safety splint

2 Linch pin

Insert the linch pin through the locking

pins and fold the locking rings forward.

1 Excenter lever

2 Locking pin

Open the excenter lever of the slideable

intake on the lift arm.

Press the cleaning head all the way

against the push handle.

Note: The less play the cleaning head

has after being installed, the less vibra-

tion will occur during cleaning.

Move the intake and insert the safety

pin and lock it into place.

Close the excenter lever.

Swivel the water reservoir all the way

down, check the lock.

The removal will take place in the opposite

order of the installation.

몇CAUTION

When the cleaning head is removed, the

stability of the appliance can be compro-

mised; ensure a safe stance.

Possibly support the rear to prevent tipping.

Replace or turn vacuum lips

Clean water distribution channel

Replacing the brush rollers

Replacing the disk brushes

Install cleaning head

Dismantling the cleaning head

20 EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher B60 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info