Bedienungsanleitung Karcher B80 (Seite 16 von 300) (Alle Sprachen)

804749

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

- 3

1OFF

Device is switched off

2Transport mode

Driving to the Place of Use.

3Eco mode

Wet clean the floor (with reduced brush

speed) and vacuum up wastewater

(with reduced suction).

4Normal mode

Wet clean the floor and vacuum up dirt

water.

5 Increased brush contact pressure

Wet clean the floor (with increased

brush contact pressure) and vacuum up

dirt water.

6Intense mode

Wet clean the floor and allow the deter-

gent to react.

7Vacuum mode

Suck in the dirt fleet.

8Polishing mode

Polishing the floor without the applica-

tion of liquid.

The disc brush must be installed before the

initial operation (see "Maintenance work").

The brushes are mounted.

Install the batteries (see "Care and Mainte-

nance/Install and connect batteries").

Prior to the initial startup, following a ser-

vice reset or when switching to another bat-

tery type, you must adjust the charging

marker line.

Use the Grey Intelligent Key.

Setting the charging marker line (see

Chapter "Grey Intelligent Key/Setting

the charging marker line“.

We recommend using our batteries as de-

scribed in chapter "Care and Maintenance/

Recommended batteries".

Note:

When using other batteries (e.g. batteries

from other manufacturers), the total dis-

charge protection level for the respective

battery must be reset by the Kärcher after-

sales service.

Note:

The device is equipped with a safety mech-

anism to prevent total discharge, i.e. when

the permissible minimum capacity is

reached, the brush motor and the turbine

are switched off.

Drive the machine directly to the charg-

ing station; avoid any steep gradients in

the process.

DANGER

Danger of injury due to electric shock. Ob-

serve the mains voltage and fuse protec-

tion on the type plate of the device.

Only use the charger in dry rooms with suf-

ficient ventilation!

– Average charging time is approx. 10 -15

hours.

– The built-in charger has electronic con-

trols and is suitable for all recommend-

ed batteries; it automatically switches

off the charging process.

– The built-in battery is shown on the dis-

play during the charging process. If this

is not the case, the charging marker line

must be selected (see "Setting the

charging marker line").

– The appliance must not be used during

the charging process.

Insert the plug of the connecting cable

into the socket. The charging process

will start.

Note: The selected battery will be dis-

played during charging.

Charge until the display shows a full

charge.

Notes on initial charge

With the initial charge, the control will not

yet be able to detect which battery type has

been installed. Keep charging the batteries

until the display shows a full charge

몇WARNING

Danger of causticization!

–Adding water to the battery in its dis-

charged state can cause the acid to

leak.

–Use safety glasses while handling bat-

tery acid and follow the safety instruc-

tions to avoid personal injury or damage

to clothes.

–Should the acid spray on to the skin or

clothes, rinse immediately with lots of

water.

ATTENTION

Risk of damage!

–Use only distilled or desalinated water

(EN 50272-T3) for filling the battery.

–Do not add any substances (so-called

performance improving agents), else

warranty claims will not be entertained.

–Replace batteries with the same battery

type only. Otherwise the charging char-

acterisitc must be readjusted by the af-

tersales service.

Insert the vacuum bar into the vacuum

bar suspension in such a manner that

the profiled sheet is positioned above

the suspension.

Tighten the wing nuts.

Insert the suction hose.

Check if the height adjustment is mounted

on the inside of the vacuum bar.

When the height adjustment is mounted

on the outside, the vacuum bar gets

caught at the bottom of the appliance.

DANGER

Risk of injury. Pull the Intelligent Key to take

all functions out of operation immediately.

Insert batteries and connect (see "Be-

fore Start-up").

Place long lateral boards of the packag-

ing as a ramp next to the pallet.

Fix the ramp on the pallet with nails.

Place short boards as a support under-

neath the ramp.

Remove the wooden bars in front of the

wheels.

Program selection switch

Before Startup

Installing the Brushes

BD model

BR model

Install batteries

Setting the charging marker line

Using batteries made by other

manufacturers

Charging battery

Charging process

Low maintenance batteries (wet

batteries)

Installing the Vacuum Bar

Unloading

16 EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher B80 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info