Bedienungsanleitung Karcher B80 (Seite 18 von 300) (Alle Sprachen)

804749

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

- 5

ATTENTION

Risk of damage to the floor covering. Do

not operate the appliance on the spot.

Turn the program selection switch to

the desired cleaning program.

The appliance controls the lowering

and raising of the cleaning head auto-

matically, depending on the selected

programme mode. The brush motor

also runs and stops automatically.

Note:

The brush motor comes to a halt when the

machine stops and when there is overload.

The appliance controls the lowering

and raising of the suction bar automati-

cally, depending on the selected pro-

gramme mode.

Note:

For cleaning tiled floors, adjust the straight

suction bar in such a way that cleaning is

not done at an angle of 90 degrees to the

joints.

The inclined position and the inclination of

the suction bar can be adjusted to achieve

better suction results (see "Adjusting the

suction bar").

If the wastewater reservoir is full, the floater

will close the suction opening and the suction

turbine will run at a higher speed. If this is the

case, shut the vacuum off and drive to empty

the wastewater reservoir.

Close the regulatory button for setting

the water quantity.

Release driving lever.

Set the program selection switch to suc-

tion or vacuuming.

Briefly drive forward and suck of the re-

maining water.

Remove the Intelligent Key.

Charge battery, if required.

몇WARNING

Please observe the local provisions regard-

ing the wastewater treatment.

Take the water discharge hose from the

support and lower above a suited col-

lection device.

Crush or bend the dosing equipment.

Open the lid of the dosing equipment.

Drain off the dirt water - regulate the

water quantity by pressing or bending.

Rinse the waste water tank with clean

water or with the rinsing system for the

waste water tank (option).

Loosen the lid for emptying the fresh

water - do not remove it fully. Drain water.

To rinse the fresh water reservoir, re-

move the cover completely and remove

the fresh water filter.

Plug in the Intelligent Key.

Select the desired function by turning

the Info button.

The different functions are described in the

following.

In this menu item, the authorisations for the

yellow Intelligent Keys are released.

Press the info button while "Key menu

>>“ is displayed.

Remove the grey Intelligent Key and in-

sert the yellow Intelligent Key to be pro-

grammed.

Select the desired menu item to be

modified by turning the Info button.

Press Info button.

Adjust the menu item by turning the Info

button.

Confirm the setting by pressing the

menu item.

Select the next menu item to be modi-

fied by turning the Info button.

To save the authorisations, retrieve the

menu "Save settings" by turning the info

button and pressing it.

To exit, retrieve the menu "Exit menu" by

turning the info button and pressing it.

Parameters that are adjusted with the grey

Intelligent Key, are kept until another set-

ting is selected.

Turn the program selection switch to

the desired cleaning program.

Turn the info button until "Cleaning App

>>“ is displayed.

Press the info button - the first adjusta-

ble parameter is displayed.

Press Info button - the set value blinks.

Set the desired value by turning the info

button.

Confirm the changed setting by press-

ing the Info button or wait till the set val-

ue is automatically accepted after 10

seconds.

Select the next parameter by turning

the Info button.

After all desired parameters have been

modified, turn the info button until "Exit

menu" is displayed.

Press the info button - you will exit the

menu.

Press Info button - the set value blinks.

Set the desired language by turning the

info button.

Confirm the changed setting by press-

ing the Info button or wait till the set val-

ue is automatically accepted after 10

seconds.

Adjust the trailing time of the brushes.

Same adjustment as "Set language".

Turn the info button until the function

"Battery menu" is displayed.

Press the info button - select the charg-

ing marker line according to the built-in

batteries.

Note: Setting the charging marker line

should be discussed with Kärcher cus-

tomer service. This applies especially if

the battery is not listed in the menu.

Confirm the changed setting by press-

ing the Info button or wait till the set val-

ue is automatically accepted after 10

seconds.

Recreate the basic settings.

DANGER

Risk of injury! When loading or unloading

the machine, it may only be operated on

gradients up to the maximum value (see

"Technical Specifications"). Drive slowly.

몇CAUTION

Risk of personal injury or damage! Mind the

weight of the appliance during transport.

Remove the brush to avoid damage to

the brushes.

Activate parking brake.

When transporting in vehicles, secure

the appliance according to the guide-

lines from slipping and tipping over.

몇CAUTION

Risk of personal injury or damage! Consid-

er the weight of the appliance when storing

it.

This appliance must only be stored in inte-

rior rooms.

Cleaning

Lower the cleaning head

Lower the vacuum bar

Shutting Down the Appliance

Drain off dirt water

Drain off clean water

Grey Intelligent Key

Key menu >>

Cleaning App >>

Setting the language

Brush trailing

Setting the charging marker line

LOAD DEFAULT

Transport

Storage

18 EN

Karcher B80 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info