Bedienungsanleitung Karcher BD 80-100 W (Seite 16 von 252) (Alle Sprachen)

804751

Zoom out

Zoom in

Vorherige Seite

1/252

Nächste Seite

16 English

Detergent

1. Fill the detergent into the fresh water

tank.

Note: The cap for the fresh water tank

filling hole can be used for measuring

the correct quantity of detergent. It has a

measuring scale marked on the inner

side.

Adjusting the water volume

1. Adjust the water volume via the regulat-

ing knob to suit the degree of soiling of

the floor covering.

Note

Perform initial cleaning tests with a low wa-

ter volume. Increase the water volume step

by step until achieving the desired cleaning

result.

Note

The cleaning head continues operating

without a liquid supply if the fresh water

tank is empty.

Adjusting the suction bar

Adjusting the inclination

The inclination must be adjusted so that the

suction lips of the suction bar make even

contact with the floor over the entire length

of the suction bar.

1. Loosen the screw.

1Screw

2. Adjust the inclination of the suction bar.

3. Tighten the screw.

Adjusting the height

The height adjustment affects the bending

of the suction lips on contact with the floor.

1. Push the device a small distance for-

wards.

2. Compare the bending of the suction lips

with the figure below.

1Spacer roller with holder

2Washer

3Screw

3. Unscrew the screw.

4. Insert a sufficient number of washers be-

tween the suction bar and spacer roller

to create the correct bending of the suc-

tion lip.

5. Fit the remaining unused washers above

the spacer roller.

6. Screw in and tighten the screw.

7. Repeat the entire procedure at the sec-

ond spacer roller.

8. Push the device a small distance for-

wards.

9. Check the bending of the suction lips

over the entire length.

10.Repeat the adjustment procedure if nec-

essary.

Cleaning

Switching on the device

1. Turn the key-operated switch to "1".

The display shows the following one af-

ter the other:

●Period of time until the next after-sales

Customer Service

●Software version, control panel

●Charging state of the battery and num-

ber of operating hours

Driving

Note

The direction of travel can be changed dur-

ing the cleaning operation. This way, a cer-

tain position can be intensively cleaned by

driving back and forth several times.

1. Set the driving direction switch to "for-

ward".

Cleaning

Note

The inclination and height of the suction bar

can be adjusted to improve the vacuuming

results (see chapter Adjusting the suction

bar).

Note

When the waste water tank is full, the float

switch closes the suction opening and the

suction turbine runs at a higher speed. In

this case, raise the suction bar and drive to

the location for emptying the waste water

tank.

1. Turn the working speed rotary knob to

the desired value.

The speed is shown on the display dur-

ing the adjustment. The display is shown

in percentage of the maximum speed.

2. Set the water volume at the regulating

valve.

3. Press the suction bar lever downwards.

The suction bar lowers.

Vacuuming begins.

4. Press the cleaning head lever down-

wards, unlatch it and allow it to move up-

wards.

5. Pull the safety switch towards the push

handle.

The cleaning head starts up and the de-

vice moves at the set speed.

Increasing the brush contact pressure

1. Let go of the safety switch.

2. Lift the cleaning head lever up with your

hand and latch it towards the right.

Finishing operation

Finishing cleaning

1. Let go of the safety switch.

2. Press the cleaning head lever down and

latch it in place.

3. Continue moving a short distance.

The residual water is vacuumed up.

4. Lift the suction bar.

The suction continues to run for 10 sec-

onds.

5. Turn the key-operated switch to "0".

6. Charge the battery if necessary.

Draining the waste water

몇WARNING

Environmental pollution!

Environmental pollution due to improper

disposal in waste water.

Observe the local waste water treatment

regulations.

1. Remove the drain hose from the support

and lower it over a suitable collecting de-

vice.

2. Press the dosing unit together or kink

the hose.

3. Open the dosing unit cover.

4. Drain the waste water. Regulate the wa-

ter volume by pressing or kinking.

5. Rinse the waste water tank with clear

water.

Draining fresh water

1. Pull off the filling level indicator hose and

swivel it down.

Quickly draining fresh water

1. Unscrew the fresh water tank cap.

2. Allow the fresh water to drain away.

3. Fit the fresh water tank cap and screw

into place.

Note: Take care to ensure that the hose

connection in the fresh water tank cap is

positioned at the lowest point in the tank

after screwing the cap in place.

Universal decoater, suitable

for linoleum

RM 754

Acidic vending machine ba-

sic cleaner. Suitable for san-

itary areas and construction

cleaning

RM 751

Industrial maintenance

cleaner

RM 69

Industrial basic cleaner and

alkaline decoater

RM 752

Surface disinfectant cleaner RM 732

Application Detergent

10 mm



12 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher BD 80-100 W Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info