Bedienungsanleitung Karcher BR 30-1 C Bp (Seite 16 von 224) (Alle Sprachen)

804745

Zoom out

Zoom in

Vorherige Seite

1/224

Nächste Seite

16 English

●The floor is cleaned by moving the device back and

forth at a speed similar to vacuum cleaning.

●Activate the Boost function for heavy soiling. To do

this, hold down the Boost function button. The roller

speed and fresh water quantity are increased when

the Boost function is activated. Allow the device to

slide slowly over the floor without exerting any pres-

sure on the device.

Illustration I

●If the cleaning rollers are blocked, e.g. by jamming,

the device switches off.

The warning light lights up.

Remove the blockage.

To switch the device on again, press the ON/OFF

switch twice.

Note

The first press clears the error, the second press switch-

es on the device.

If the ON/OFF switch is not pressed, the warning light

goes out after 10 s. To switch on the device, press the

ON/OFF switch once.

Illustration J

●If the capacity of the battery pack is almost exhaust-

ed, the ON/OFF switch starts to flash.

Illustration K

Press the ON/OFF switch.

The device switches off.

Take the battery pack out of the device and charge

it (see chapter Ending operation).

Note

In order to avoid a damaging exhaustive discharge of

the battery pack, the device switches itself off before the

battery pack is completely discharged.

●Switch off the device and move it to the parking po-

sition whenever work is interrupted and at the end of

work. When the device is in the parking position, the

cleaning rollers do not touch the floor.

Illustration L

●When parking the device, do not lean it against

walls, doors or other objects; instead, bring the de-

vice into the parking position.

Illustration M

Starting work

ATTENTION

Uncontrolled motion

Damage to the device and material damage

The cleaning rollers start rotating as soon as the device

is switched on.

Hold the handle tight to prevent the device from moving

away independently.

ATTENTION

Fresh water tank or waste water tank not installed

Material damage

Before starting cleaning work, ensure that the fresh wa-

ter tank is filled with water and the waste water tank is

fitted in the device.

1. Remove the cleaning rollers from the device (see

chapter Cleaning the cleaning roller).

2. Moisten the cleaning rollers with fresh water.

3. Install the cleaning rollers.

4. Press the ON/OFF switch.

Illustration N

The device switches on.

5. Activate the boost function to clean stubborn dirt

(see chapter General notes on operation).

Emptying the waste water tank

●Empty the waste water tank as soon as the fresh

water tank is empty, or the device no longer absorbs

moisture, and water remains on the floor.

1. Press the ON/OFF switch.

Illustration L

The device switches off.

2. Bring the device into the parking position (see chap-

ter General notes on operation).

3. Disengage the two locking flaps on the device.

Illustration O

The waste water tank releases from the device.

4. Lift the device and set it aside.

5. To transport it to the emptying point, do not hold the

waste water tank by the lid, but with both hands on

the side of the drip tray. Keep the waste water tank

level, otherwise waste water can escape.

6. Empty the waste water tank.

Illustration P

In the case of stubborn dirt, rinse out the waste wa-

ter tank with tap water (see chapter Cleaning the

waste water tank).

7. Clean the sweep bins (see chapter Cleaning the

sweep bins).

8. Insert the waste water tank into the device in reverse

order.

Interrupting operation

ATTENTION

Risk of damage due to moisture and detergents as

well as the device tipping over

Risk of material damage on sensitive floors and on the

cleaning rollers due to prolonged exposure to moisture

and detergents.

Risk of material damage if the device falls over.

Always move the device to the parking position when

you take a break from work and after work.

Do not lean the device against walls, doors or other ob-

jects when setting it down.

1. Press the ON/OFF switch.

Illustration L

The device switches off.

2. Bring the device into the parking position (see chap-

ter General notes on operation).

Rinsing the cleaning rollers

The rinsing function can be used for intermediate clean-

ing of the cleaning rollers in case of severe dirt accumu-

lation.

Note

At the end of work and before storing the device, the

cleaning rollers must be removed and cleaned under

running water or in the washing machine (see chapter

Cleaning the cleaning roller). The rinsing function does

not replace final basic cleaning.

1. Press the ON/OFF switch.

Illustration L

The device switches off.

2. Bring the device into the parking position (see chap-

ter General notes on operation).

3. Check the filling level in the fresh water tank, it must

be at least 50%.

If necessary, fill the fresh water tank accordingly

(see chapter Filling the fresh water tank).

4. Press and hold the Boost function button.

Illustration Q

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher BR 30-1 C Bp Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info