Bedienungsanleitung Karcher HDS 1000 BE (Seite 23 von 428) (Alle Sprachen)

726230

Zoom out

Zoom in

Vorherige Seite

1/428

Nächste Seite

– 4

– Check the high-pressure hose daily.

Do not use hoses with kinks.

Stop using the high-pressure hose if the

external wire layer is visible.

– Do not use the high-pressure hose any-

more if the winding is damaged.

– Lay the high-pressure hoses in such a

way that no vehicle can drive over it.

– Do not use high-pressure hoses that

have been driven over, kinked, pressed

or bent even if there is no externally vis-

ible damage.

– Store the high-pressure hoses in such a

way that they are not subject to any me-

chanical load.

Safety devices serve for the protection of the

user and must not be put out of operation or

bypassed with respect to their function.

The safety mechanism against lack of water

prevents the heater from over-heating when

there is no water. The burner operates only

when there is adequate water supply.

– If the hand spray gun is closed, the

overflow valve opens and the high pres-

sure pump diverts the water back to the

pump suction side. Thus the permissi-

ble working pressure is not exceeded.

– The overflow valve is set by the manu-

facturer and sealed. Setting only by

customer service.

– The safety valve opens when the over-

flow valve is defective.

– The safety valve is set by the manufac-

turer and sealed. Setting only by cus-

tomer service.

The pressure switch switches off the burner

when the working pressure falls below the

minimum value and switches it on again

when it is exceeded.

The safety catch on the trigger gun pre-

vents the appliance from being switched on

unintentionally.

몇 WARNING

Risk of injury! Appliance, accessories, sup-

ply lines and connections must be in fault-

free condition. If they are not in a perfect

state then the appliance must not be used.

 Attach both spray lance rests before in-

itial startup (see figure A at the begin-

ning of these instructions).

ATTENTION

Risk of damage! In case of lacteous oil inform

Kärcher customer service immediately.

 Check oil level of the high pressure

pump at the oil sight glass.

Do not operate the appliance if the oil level

has fallen below "MIN".

 Add oil if required (see technical speci-

fications).

Follow the instructions given in the sec-

tion "Safety Notes"!

 Read the operating instructions of the

engine manufacturer before start-up

and follow the safety instructions care-

fully.

 Check air filter.

 Check oil level of the engine.

Do not operate the appliance if the oil level

has fallen below "MIN".

 If required, top up oil carefully.

 Fill the fuel tank with unleaded petrol.

Do not use 2-speed mixture.

 Fill fuel tank with diesel.

Safety Devices

Water shortage safeguard

Overflow valve

Safety valve

Pressure switch

Safety catch

Start up

Attaching the spray lance rest

Check oil level of the high pressure

pump

Motor

HDS 1000 BE:

HDS 1000 DE:

23EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher HDS 1000 BE Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info