Bedienungsanleitung Karcher HDS 13-35 De Tr1 (Seite 29 von 512) (Alle Sprachen)

726237

Zoom out

Zoom in

Vorherige Seite

1/512

Nächste Seite

- 9

If the appliance is not used for an ex-

tended period and if there is frost, re-

move the battery and store it in a loca-

tion protected from frost.

With external water supply: Disconnect

the water hose from the water supply.

Set the power switch to "0/OFF“ (burner

off).

Unpressurize the appliance.

Set the power switch to the operating

mode "frost protection".

HDS 13/20, HDS 17/20 only:

Set the detergent dosing valve to maxi-

mum. Pull the detergent suction hose

out of the detergent container and store

it in such a way that it can be evacuated.

Open the supply tap of the water tanks

and the drain tap in order to completely

drain the device. The filling level indica-

tor of the water tanks dips completely.

Close the supply tap of the water tanks

and the drain tap.

Disconnect the trigger gun from the

high-pressure hose.

Connect the high-pressure hose to the

frost protection inlet.

Connect the water hose to the return

flow of the frost protection.

Prepare the antifreeze in the antifreeze

container. Select the mixing ratio of the

water/antifreeze as per the instructions

of the antifreeze manufacturer.

Check the antifreeze concentration with

a commercially available antifreeze

tester and adapt if necessary.

Open the filling hole of the float contain-

er. In order to do so, loosen the wing

screw and push the cover to the left.

Fill 20 litres of antifreeze into the float

container and close the filling hole.

Align the actuation lever of the ball tap

for antifreeze vertically.

Place the actuation lever of the return

flow valve ball tap parallel to the travel

direction (20L).

With cold engine only:

To preheat the motor, turn the key

switch to the left and hold it until the in-

dicator light preheating goes out.

Turn key switch to position "I". The indi-

cator lamp for operational readiness

lights up.

The control voltage is switch on and the

display shows the operating status "An-

tifreeze".

Turn the key switch to the right until the

motor is running.

The antifreeze liquid is pumped through

the appliance in a circuit.

Lead the residual water via the frost

protection hose into the anti-freeze con-

tainer.

As soon as antifreeze exits the anti-

freeze hose, put the operating lever of

the frost protection ball tap in the hori-

zontal position and wait for 5 seconds.

Switch off the motor.

Set the power switch to "0/OFF“ (burner

off).

Note: Prior to operation, the antifreeze

must be pumped from the high-pressure

system back into the antifreeze container.

Align the actuation lever of the ball tap

for antifreeze vertically.

Connect the high-pressure hose to the

frost protection inlet.

Connect the water hose to the return

flow of the frost protection.

Open the filling hole of the float contain-

er. In order to do so, loosen the wing

screw and push the cover to the left.

Fill 20 litres of fresh water into the float

container and close the filling hole.

Set the power switch to the operating

mode "frost protection".

With cold engine only:

To preheat the motor, turn the key

switch to the left and hold it until the in-

dicator light preheating goes out.

Turn key switch to position "I". The indi-

cator lamp for operational readiness

lights up.

The control voltage is switch on and the

display shows the operating status "An-

tifreeze".

Turn the key switch to the right until the

motor is running.

The antifreeze fluid is forwarded from

the float container into the antifreeze

container with fresh water.

Rinse for approx. 2 minutes until the an-

tifreeze container is filled.

Switch off the motor.

Set the power switch to "0/OFF“ (burner

off).

Frost protection battery

Antifreeze rinse in the circuit (high

pressure pump)

Pumping antifreeze out of the high

pressure system

29EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher HDS 13-35 De Tr1 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info