Bedienungsanleitung Karcher HDS 13-35 De Tr1 (Seite 28 von 512) (Alle Sprachen)

726237

Zoom out

Zoom in

Vorherige Seite

1/512

Nächste Seite

- 8

– Position parallel to travel direction: The

return water from the high-pressure

pump flows into the float tank when the

overflow valve is open.

Note: If the trigger gun is closed in this

ball tap position, the device may switch

off after a few minutes due to too high

temperature (see Troubleshooting/ER-

ROR 3).

– Position lateral to travel direction: The

return water of the high-pressure pump

flows into the water tanks when the

overflow valve is open.

Place the actuation lever of the return

flow valve ball tap parallel to the travel

direction (20L).

Close the supply tap of the water tanks.

Set the actuation lever of the return flow

valve ball tap lateral to the travel direc-

tion (500L).

Open the supply tap of the water tanks.

Note: The device can only be operated

when the front cover is closed. If the front

cover is opened, the device shuts down

and the indicator light is on.

Note: Due to the bleeding procedure, the

speed of the motor may vary until the final

operating pressure has been reached.

Unlock the emergency-stop switch by

pulling.

Open rear cover.

Establish the water supply.

Insert the key into the key switch.

With cold engine only:

To preheat the motor, turn the key

switch to the left and hold it until the in-

dicator light preheating goes out.

Turn key switch to position "I". The indi-

cator lamp for operational readiness

lights up.

The control voltage is switch on and the

display shows the operating status.

Turn the key switch to the right until the

motor is running.

Set the appliance switch to operation

with cold/ hot water.

Release the trigger gun. To do so, push

the safety catch towards the back.

Open the hand spray gun.

Set the power switch to "0/OFF“ (burner

off).

DANGER

Scalding danger!

Set the power switch to the desired

working temperature (max. 100 °C).

The burner is switched on.

HDS 9/50, HDS 13/35 only (optional with

HDS 13/20, HDS 17/20):

Note: If the motor speed is increased, the

operating pressure also rises. This can be

read from the pressure gauge.

– Increasing the speed:

Push up the lever of the speed control.

– Reducing the speed:

Push down the lever of the speed con-

trol.

HDS 13/20, HDS 17/20 only:

Set (+/-) the working pressure and

quantity by turning the pressure/ quan-

tity regulation mechanism at the hand

spray gun.

DANGER

Risk of injury! When adjusting the pressure/

quantity regulation, make sure that the

screw connection of the spray lance does

not become loose.

HDS 13/20, HDS 17/20 only:

ATTENTION

Unsuitable detergents can cause damage

to the appliance and to the object to be

cleaned.

– For considerate treatment of the envi-

ronment use detergent economically.

– Observe the dosage and other instruc-

tions provided with these detergents.

– Use only those detergents approved by

the manufacturer of the appliance.

– Kärcher detergents ensure smooth

functioning. Please consult us or ask for

our catalogue or our detergent informa-

tion sheets.

Place the detergent suction hose in a

container filled with detergent and tight-

en the screw cap.

Set dosing value for detergent to the

desired concentration.

Note: To prevent detergent flowing back

into the float tank or water tanks during op-

eration with detergent with the trigger gun

closed, ensure the detergent dosing valve

is closed.

HDS 13/20, HDS 17/20 only (optional):

Note: The (optional) speed control attach-

ment kit is essential when operating weed

removal!

This must be operated in accordance with

Weed Removal operating instructions WR

20/WR 50, Part no. 5.967-071.0!

The following information must also be ob-

served:

Push the lever of the speed control

down as far possible.

Set the device switch to the "Weed re-

moval" operating mode.

1 TEMP LOW appears on display: Heat-

ing-up time in progress (approx. 2 min-

utes)

2 TEMP OKAY appears on display:

Perform weed removal.

Close the hand spray gun.

Secure the trigger gun. To do so, push

the safety catch towards the front.

Note: If the trigger gun is closed, the motor

continues to run at idling speed. The water

therefore flows between float tank and

high-pressure pump and is heated up.

Once the maximum permissible tempera-

ture (55 °C) has been reached, the temper-

ature sensor motor is switched off at the

water inlet. After it has cooled down to be-

low 50 °C, the device can be started up

again.

HDS 13/20, HDS 17/20 only:

Set dosing value for detergent to "0".

Open the hand spray gun and rinse the

appliance for at least 1 minute.

DANGER

Danger of scalding by hot water. After oper-

ation with hot water, the device must be op-

erated with open end handgun with cold

water for at least two minutes.

ATTENTION

Risk of damage! Never stop the motor un-

der full load when the trigger gun is opened.

Set the power switch to "0/OFF“ (burner

off).

Close the hand spray gun.

Motor regulates to reach dry run speed.

Turn the key switch to "0". The opera-

tion readiness indicator lamp goes off.

The control voltage is switched off and

the display goes out.

With external water supply: Shut off wa-

ter supply.

Activate trigger gun until device is pres-

sure-less.

Secure the hand spray gun using the

safety catch so that it doesn't open ac-

cidentally.

With external water supply: Disconnect

the water hose from the water inlet and

coil up the water hose onto the hose

reel.

Coil the high-pressure hose onto the

hose reel.

To protect from freeze damages, the appli-

ance must be flushed with antifreeze.

Note:Use normal glycol-based anti-freez-

ing agents for automobiles.

Note: Observe handling instructions of the

anti-freeze agent manufacturer.

A certain corrosion protection is achieved

with this as well.

Check the coolant circuit of the motor

for sufficient antifreeze, refill antifreeze

as needed.

See Maintenance Procedures "Check

and refill the coolant“.

Return flow valve ball tap

External water supply

Internal water supply

Turning on the Appliance

Operating with cold water

Operating with hot water

Speed control

Set working pressure and flow rate

Operation with detergent

Removal of weeds

Interrupting operation

After operation with detergent

Turn off the appliance

Frost protection

Antifreeze motor

28 EN

Karcher HDS 13-35 De Tr1 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info