Bedienungsanleitung Karcher KM 100-100 R Bp (Seite 25 von 396) (Alle Sprachen)

804786

Zoom out

Zoom in

Vorherige Seite

1/396

Nächste Seite

- 9

Replacement is due if a visible deteriora-

tion in sweeping performance caused by

bristle wear is evident.

Park the sweeper on an even surface.

Set programme switch to step 1 (driv-

ing). Roller brush is raised.

Turn main key to "0" and remove it.

Press emergency-stop button.

Secure the machine with wheel

chock(s) to prevent it from rolling away.

Raise slightly the waste containers on

both sides and pull them out.

Loosen the front attachment screw of

the right-hand side panel.

Loosen the rear attachment screw on

the right-hand side panel.

Remove side panel.

Loosen the screws.

Loosen the attachment screw of the

bowden cable and remove the bowden

cable.

Unscrew the screw on the pivoting point

of the roller brush arm.

Pull out roller brush swinging arm.

Remove the roller brush cover.

Pull out roller brush.

Installation position of roller brush in direc-

tion of travel

Push new roller brush into the roller

brush housing and onto the drive pin.

Note: When installing the new roller brush,

ensure correct positioning of the bristle as-

sembly.

Note: Adjust the bowden cable, so that the

roller brush is lifted approx. 10 mm off the

floor.

Position roller brush cover.

Install the roller brush arm.

Hook the Bowden cable in.

Tighten the fastening screws.

Screw on side panel.

Push in the waste containers on both

the sides and lock them.

Set programme switch to step 1 (driv-

ing). The side brush and roller brush are

raised.

Drive sweeper on to a smooth, even

surface covered with a visible layer of

dust or chalk.

Set programme switch to step 2. Roller

brush is lowered. Slightly press down

on the drive pedal and allow the sweep

brush to briefly rotate.

Raise roller brush.

Press pedal which raises bulk waste

flap and keep pressed.

Drive machine backwards.

The sweeping track should have an even

rectangular shape which is between 50 and

70 mm wide.

Note: The side brush floating mounting of

the roller brush adjusts the sweeping track

as the bristles wear down. The roller brush

must be replaced if it becomes too worn.

Park the sweeper on an even surface.

Set programme switch to step 1 (driv-

ing). Roller brush is raised.

Turn main key to "0" and remove it.

Press emergency-stop button.

Secure the machine with wheel

chock(s) to prevent it from rolling away.

Raise slightly the waste containers on

both sides and pull them out.

Open the fastening screws of the side

panels on both sides.

Remove side panels.

Front sealing strip

Slightly loosen retaining nuts for the

front sealing strip; to replace, unscrew.

Screw on new sealing strip without fully

tightening the nuts.

Replacing roller brush Check the sweeping mirror of the

sweeping roller

Adjusting and replacing sealing strips

25EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher KM 100-100 R Bp Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info