Bedienungsanleitung Katadyn PowerSurvivor 160E (Seite 14 von 36) (Englisch)

522391

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

If you plan to run the watermaker again within a couple of days, it can simply be turned off. If

you do not intend to use your watermaker again within a week, it should be treated with

membrane preservative to prevent organic growth on the membrane.

Note: Organic growth is much more rapid in warm or tropical climates. If using the watermaker

in a tropical environment, we recommend a membrane preservative treatment if the watermaker

will not be run again within the next three days! Before doing repairs or maintenance work

on a PowerSurvivor, close the seawater inlet valve after turning off the system.

Otherwise, the possibility exists that hose failure, for example, could cause the boat to

sink.

At the end of a watermaker run, check the condition of water in the prefilter housing. If there is

evidence of trapped material, clean the prefilter housing and install a clean prefilter element.

Special Conditions

Product freshwater output volume will vary depending on the salinity and temperature of the

seawater being processed. Figure 6 illustrates the relationship between feed water temperature

and the quantity of product water. Factors which are known to affect output or performance

include:

• High Salinity will decrease output

slightly and lead to a modest

increase in current draw. Effectively,

the pump must work harder to

remove a larger percentage of dis-

solved solids from the seawater.

• Cold Water will have an effect

similar to that of high salinity.

• Silt or Sand can damage the

membrane and internal pump

components if not removed during

prefiltration. If you must regularly

process such water, consider

installing a Silt Reduction Kit (see

Kits & Accessories).

• Foul Intake Seawater can seriously

effect the quality of the product freshwater. The watermaker membrane is designed to

remove the impurities found in clean, open ocean seawater. Processing of seawater with

other kinds of impurities (1) may not remove those impurities and (2) may damage or

destroy the membrane. See Maintenance and Service: Prefilter Maintenance below for

more information on typical problems associated with foul water intake.

• Low Battery Voltage will dramatically reduce the volume of seawater throughput and

product freshwater output. We recommend not operating the watermaker if battery

voltage is below 11 VDC.

Note on Red Tides: In many areas of the ocean, a phenomenon generally known as a

“red tide” can occur. This generic name is used to describe an invasion of local waters by

huge populations of micro-organisms, which turns the seawater red. Occasionally, a red tide

is accompanied by the death of local fish and other sea life, which can cause serious local

pollution of the seawater. Although the watermaker membrane can remove the

microorganisms that cause the red tide, it can not remove all of the chemical pollutants

caused by large-scale biological decomposition. Therefore, we do not recommend using the

watermaker to process seawater when a red tide is present.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Katadyn PowerSurvivor 160E Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Katadyn PowerSurvivor 160E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info