Bedienungsanleitung Katadyn PowerSurvivor 80E (Seite 12 von 36) (Englisch)

522392

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

• petroleum products, such as oil, fuel, thinners, paints, paint removers, etc.

• chlorine-treated water (for example, most “dockside” water)

• silty water—water contaminated by fine, hard, suspended particulates

• putrid water, “red tides”, or any seawater that smells or looks contaminated

It is important to remember that the watermaker is designed to process clean, open-ocean

seawater. Any departure from that standard for your seawater intake runs the risk of causing

excessive wear or damage to internal pump parts and/or the vulnerable reverse osmosis

membrane, or producing contaminated product freshwater.

Note: Judging the quality of seawater input always involves a certain calculated risk. We

know of watermaker systems that have been destroyed far offshore by intaking fresh whale

excrement or oil contaminants from natural seepages—still, the chance of such things

happening is normally small. On the other hand, regularly running a watermaker in an

enclosed marina or harbor runs a much higher risk of harmful contamination. If you need to

test a new installation while in a marina or harbor, monitor the water quality around your

vessel carefully while testing. Most of the time you should be able to run the watermaker

safely for enough time to check out the system. Don’t sail away without testing a new

installation or repair!

Startup: Turn on the electric power to the watermaker. If there is air in the seawater intake

plumbing, the pump may require several minutes to draw up enough water to fill the hoses,

prefilter housing, pump and membrane housing. Since the pump is self-priming, there is no

need to prime the system prior to running. Shortly after the hoses and prefilter housing have

filled with seawater, reject brine water should start discharging from the pump.

Test and Run: When all air has been forced out of the system (which may take several

minutes more), product freshwater should begin to flow from the hose barb at the end of the

membrane housing. It is normal for product water to be unpotable for a short time after startup.

Reject the initial product water and use the TDS meter and/or taste test to monitor the quality

until it is acceptable. This will usually take about 5–10 minutes. When good quality water is

flowing continuously, direct the product freshwater output to your freshwater collection tank.

Continue to run until the desired quantity of water has been produced.

Shutdown and Storage: When the desired amount of water has been produced, the

product freshwater quality should be checked again. If water quality is good at both the

beginning and end of the run, it is likely that the collected water is good and can be safely

transferred to the ship’s potable water storage tank.

If you plan to run the watermaker again within a couple of days, it can simply be turned off. If

you do not intend to use your watermaker again within a week, it should be treated with

membrane preservative to prevent organic growth on the membrane.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Katadyn PowerSurvivor 80E Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Katadyn PowerSurvivor 80E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info