Bedienungsanleitung Katadyn PowerSurvivor 80E (Seite 18 von 36) (Englisch)

522392

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

The only indication that the membranes might benefit from cleaning is a substantial reduction in

the quantity of product freshwater output, all other factors being normal (e.g., battery voltage,

salinity, seawater temperature). The best way to detect such a problem is by keeping an

accurate log of product freshwater output at known battery voltages. Such a practice is highly

recommended.

If you have determined that your membranes need cleaning and you know the type of deposits

(mineral or organic), use the appropriate cleaner. If you do not know the nature of the deposits,

try cleaning first with the

Alkaline Cleaner and check for improvement in product

freshwater output. If output remains poor, repeat the cleaning process using the

Acid

Cleaner

. Never mix the two types of cleaners! Always flush well with clean water between

processes if performing both alkaline and acid cleaning. The following directions apply for both

types of membrane cleaners:

1. Turn the clean/run valve lever on the pump to its “clean” position (see Figure 8).

2. Discard any dirty seawater in the prefilter assembly. Clean the housing and install a clean

element

3. Fill a clean plastic container or bucket with one gallon (approximately 4 liters) of clean

water. Freshwater is preferable, but clean seawater may be used if freshwater is not

available. (Caution: Never use chlorinated freshwater. This may damage the

membrane.)

4. Mix four spoonful (approximately 40 grams) of either Acid Cleaner or Alkaline Cleaner

(not both!) with the water in the container and stir until the cleaner is completely

dissolved. The water should be warm, but not over 120° F (49° C).

5. Turn the lever on the prefilter 3-way valve to the alternate intake position. Run the 1/4"

alternate intake hose with the strainer attached into the container of cleaning solution.

6. Disconnect the reject brine water hose from its drain (or use a separate length of hose) to

route the reject brine water back into the container of cleaning solution during the

following procedure.

7. Turn on the watermaker. Discard any solution coming from the reject brine hose for about

30 seconds. Then run the reject brine water hose back into the container of cleaning

solution to allow recirculation of the cleaner.

8. Continue to run the watermaker for about 15 minutes, to assure that the cleaning solution

is well circulated through the pump and membrane housing.

9. Turn off the watermaker and allow the membranes to soak in the cleaning solution for 5

to 10 hours, or overnight. For severe fouling, repeat Steps 8 and 9 of this procedure.

10. When the soaking is finished, remove the reject brine hose from the cleaning solution

container and run the watermaker again. Discard the first pulses of the reject brine water.

When the reject brine flow becomes cleaner, return the reject brine hose to the cleaning

solution container for recirculation.

11. Continue to run the watermaker and recirculate the cleaning solution for another 30 to 60

minutes

12. When cleaning is complete, turn off the watermaker. Reconnect the reject brine hose to

its normal drain location.

13. Remove the alternate intake hose and strainer from the cleaning solution and place them

into a container of clean, warm (non-chlorinated) freshwater. If freshwater is not

available, clean seawater may be used if its temperature is above 68° F (20° C).

14. Turn on the watermaker and flush warm water through the system for 5 minutes.

If the watermaker will be stored for more than a week (three days in warm climates), it should

now be treated with the membrane preservative solution.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Katadyn PowerSurvivor 80E Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Katadyn PowerSurvivor 80E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info